Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > PTC Heater Circuit

for Preparation Click here


DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.

WIRING DIAGRAM


E200726E01


INSPECTION PROCEDURE

1.INSPECT PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3)


    E199507
  1. Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.

  1. Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3)
OK


2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    E197830E02
  1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F42-3 (PTC1) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 79°C (174°F) or less
    5. Headlight dimmer switch off
    6. Blower switch off
    Below 1 V*
    F42-22 (PTC2) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 76°C (169°F) or less
    5. Headlight dimmer switch off
    6. Blower switch off
    F42-4 (PTC3) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 73°C (163°F) or less
    5. Headlight dimmer switch off
    6. Blower switch off
    F42-3 (PTC1) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 79°C (174°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on
    11 to 14 V*
    F42-22 (PTC2) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 76°C (169°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on
    F42-4 (PTC3) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 73°C (163°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)

    HINT:
    *: After the measurement conditions are met, wait 30 seconds before performing measurements.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER)
  1. Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.

  1. Disconnect the F42 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 1 - F42-3 (PTC1)
    Always
    Below 1 Ω
    PTC NO. 1 relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - AIR CONDITIONING AMPLIFIER)
  1. Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.

  1. Disconnect the F42 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 2 relay terminal 1 - F42-22 (PTC2)
    Always
    Below 1 Ω
    PTC NO. 3 relay terminal 1 - F42-4 (PTC3)
    PTC NO. 2 relay terminal 1 - Body ground
    Always
    10 kΩ or higher
    PTC NO. 3 relay terminal 1 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - QUICK HEATER)
  1. Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.

  1. Disconnect the F85 heater connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 3 - F85-2 (B)
    Always
    Below 1 Ω
    PTC NO. 1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - QUICK HEATER)
  1. Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.

  1. Disconnect the F85 heater connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 2 relay terminal 3 - F85-3 (B)
    Always
    Below 1 Ω
    PTC NO. 3 relay terminal 3 - F85-1 (B)
    PTC NO. 2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    PTC NO. 3 relay terminal 3 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY AND BODY GROUND)


    E200635E02
  1. Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 2 - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
PTC NO. 1 Relay
*a
Component without relay installed
(Engine Room No. 1 Relay Block, Junction Block)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - BATTERY AND BODY GROUND)


    E200727E01
  1. Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 2 relay terminal 5 - Body ground
    Always
    11 to 14 V
    PTC NO. 3 relay terminal 5 - Body ground

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 2 relay terminal 2 - Body ground
    Always
    Below 1 Ω
    PTC NO. 3 relay terminal 2 - Body ground

Text in Illustration 
*1
PTC NO. 2 Relay
*2
PTC NO. 3 Relay
*a
Component without relay installed
(Engine Room No. 2 Relay Block)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT QUICK HEATER ASSEMBLY


    E140255E08
  1. Remove the quick heater assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (B) - 1 (E)
    Always
    Below 1 kΩ
    2 (B) - 1 (E)
    2 (B) - 2 (E)
    3 (B) - 2 (E)



NG
REPLACE QUICK HEATER ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (QUICK HEATER - BODY GROUND)


    E179945E07
  1. Disconnect the F86 heater connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F86-1 (E) - Body ground
    Always
    Below 1 Ω
    F86-2 (E) - Body ground

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Quick Heater Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)