AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > PTC Heater Circuit |

| 1.INSPECT PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3) |
![]() |
Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.
Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F42-3 (PTC1) - Body ground |
| Below 1 V* |
| F42-22 (PTC2) - Body ground |
| |
| F42-4 (PTC3) - Body ground |
| |
| F42-3 (PTC1) - Body ground |
| 11 to 14 V* |
| F42-22 (PTC2) - Body ground |
| |
| F42-4 (PTC3) - Body ground |
|
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER) |
Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.
Disconnect the F42 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 1 relay terminal 1 - F42-3 (PTC1) | Always | Below 1 Ω |
| PTC NO. 1 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - AIR CONDITIONING AMPLIFIER) |
Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.
Disconnect the F42 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 2 relay terminal 1 - F42-22 (PTC2) | Always | Below 1 Ω |
| PTC NO. 3 relay terminal 1 - F42-4 (PTC3) | ||
| PTC NO. 2 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| PTC NO. 3 relay terminal 1 - Body ground |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - QUICK HEATER) |
Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.
Disconnect the F85 heater connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 1 relay terminal 3 - F85-2 (B) | Always | Below 1 Ω |
| PTC NO. 1 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - QUICK HEATER) |
Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.
Disconnect the F85 heater connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 2 relay terminal 3 - F85-3 (B) | Always | Below 1 Ω |
| PTC NO. 3 relay terminal 3 - F85-1 (B) | ||
| PTC NO. 2 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| PTC NO. 3 relay terminal 3 - Body ground |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY AND BODY GROUND) |
![]() |
Remove the PTC NO. 1 relay from the engine room No. 1 relay block, junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 1 relay terminal 5 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 1 relay terminal 2 - Body ground | Always | Below 1 Ω |
| *1 | PTC NO. 1 Relay |
| *a | Component without relay installed (Engine Room No. 1 Relay Block, Junction Block) |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - BATTERY AND BODY GROUND) |
![]() |
Remove the PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 2 relay terminal 5 - Body ground | Always | 11 to 14 V |
| PTC NO. 3 relay terminal 5 - Body ground |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PTC NO. 2 relay terminal 2 - Body ground | Always | Below 1 Ω |
| PTC NO. 3 relay terminal 2 - Body ground |
| *1 | PTC NO. 2 Relay |
| *2 | PTC NO. 3 Relay |
| *a | Component without relay installed (Engine Room No. 2 Relay Block) |
|
| ||||
| OK | |
| 9.INSPECT QUICK HEATER ASSEMBLY |
![]() |
Remove the quick heater assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (B) - 1 (E) | Always | Below 1 kΩ |
| 2 (B) - 1 (E) | ||
| 2 (B) - 2 (E) | ||
| 3 (B) - 2 (E) |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (QUICK HEATER - BODY GROUND) |
![]() |
Disconnect the F86 heater connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F86-1 (E) - Body ground | Always | Below 1 Ω |
| F86-2 (E) - Body ground |
| *a | Front view of wire harness connector (to Quick Heater Assembly) |
|
| ||||
| OK | ||
| ||