Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (for Radio and Display Type)

REAR VIEW MONITOR SYSTEM (for Radio and Display Type) > Image from Camera for Rear View Monitor is Abnormal

for Preparation Click here


DESCRIPTION

The display signal from the rear television camera assembly transmits to the radio and display receiver assembly.

WIRING DIAGRAM


E220174E08


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the G50 radio and display receiver assembly connector.

  1. Disconnect the Y2 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G50-11 (CA+) - Y2-6 (CB+)
    Always
    Below 1 Ω
    G50-12 (V+) - Y2-3 (CV+)
    Always
    Below 1 Ω
    G50-23 (CGND) - Y2-5 (CGND)
    Always
    Below 1 Ω
    G50-24 (V-) - Y2-2 (CV-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G50-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    G50-12 (V+) - Body ground
    Always
    10 kΩ or higher
    G50-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    G50-24 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
E225824E55
  1. Reconnect the G50 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G50-23 (CGND) - Body ground
    Always
    Below 1 Ω
    G50-24 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G50-11 (CA+) - G50-23 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7.0 V

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
  1. Reconnect the Y2 rear television camera assembly connector.



  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


    E282882E04


    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)
    *b
    Waveform 1 (under normal conditions)
    *c
    Waveform 2 (camera lens is covered, blacking out the screen)
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    G50-12 (V+) - G50-24 (V-)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)