Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate

for Preparation Click here


DESCRIPTION

When the back door power window is fully closed and the rear window defogger switch is turned on, a rear window defogger activation request signal is sent via the LIN communication line to the air conditioning amplifier.

WIRING DIAGRAM


B241937E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. Since the window defogger system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
  3. Since the window defogger system does not operate if the back power window is not operating normally, confirm that the back power window of the power window system is operating normally before performing troubleshooting.

1.PERFORM ACTIVE TEST USING TECHSTREAM (DEFOGGER RELAY [REAR])
  1. Using the Techstream, perform the Active Test (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    DEF relay operation
    OFF/ON
    -

    OK:
    The DEF relay operates normally.



NG
Go to step 3
OK


2.REPLACE HEATER CONTROL ASSEMBLY
  1. Temporarily replace the heater control with a new or normally functioning one (Click here).

  1. Check the rear defogger function.

    OK:
    The window defogger function operates normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (HEATER CONTROL ASSEMBLY IS DEFECTIVE) 

3.INSPECT DEF RELAY


    B242124E01
  1. Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage applied between terminals 1 and 2
    Below 1 Ω
    3 - 5
    Battery voltage not applied between terminals 1 and 2
    10 kΩ or higher



NG
REPLACE DEF RELAY
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY - DEF RELAY)


    B242123E01
  1. Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DEF relay terminal 2 - Body ground
    Ignition switch off
    Below 1 V
    DEF relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V
    DEF relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to DEF Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - DEF RELAY AND BODY GROUND)
  1. Disconnect the F42 air conditioning amplifier connector.

  1. Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DEF relay terminal 1 - F42-38 (RDEF)
    Always
    Below 1 Ω
    F42-14 (GND) - Body ground
    Always
    Below 1 Ω
    F42-38 (RDEF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Reconnect the F42 air conditioning amplifier connector.



    E183334E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F42-38 (RDEF) - F42-14 (GND)
    Ignition switch ON, defogger switch on
    11 to 14 V
    F42-38 (RDEF) - F42-14 (GND)
    Ignition switch ON, defogger switch off
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS - DEF RELAY AND BODY GROUND)
  1. Disconnect the W1 and W2 back door glass (window defogger wire) connectors.

  1. Remove the DEF relay from the engine room relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DEF relay terminal 3 - W1-1
    Always
    Below 1 Ω
    W2-1 - Body ground
    Always
    Below 1 Ω
    W1-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR GLASS (WINDOW DEFOGGER WIRE) (Click here)