Home › Drivetrain ยท VF2BM TRANSFER / 4WD / AWD › TRANSFER CASE REAR OIL SEAL

TRANSFER CASE REAR OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN TRANSFER OIL


C216677
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the transfer oil.



2. REMOVE REAR PROPELLER SHAFT ASSEMBLY
(Click here)


3. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Remove the rear output shaft companion flange sub-assembly using the same procedure as for the front output shaft companion flange sub-assembly.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



4. REMOVE REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using a screwdriver and hammer, remove the rear transfer output shaft companion flange oil seal.



5. REMOVE TRANSFER CASE REAR OIL SEAL


F043484E01
  1. Using SST, tap out the transfer case rear oil seal.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the transfer case rear oil seal and rear case contact surface.



6. INSTALL TRANSFER CASE REAR OIL SEAL


F043486E02
  1. Coat the lip of a new transfer case rear oil seal with MP grease.

  1. Using SST and a hammer, tap in the transfer case rear oil seal until its surface is flush with the rear case upper surface.

    SST
    09223-46011  
    09631-32020  



7. INSTALL REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Tap in a new rear transfer output shaft companion flange oil seal using the same procedure as for the front transfer output shaft companion flange oil seal.

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



8. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


C217384E01
  1. Install the rear output shaft companion flange sub-assembly onto the drive sprocket sub-assembly.

  1. Using SST to hold the rear output shaft companion flange sub-assembly, install a new lock nut.

    SST
    09330-00021  

    Torque:
    118 N*m{ 1203 kgf*cm , 87 ft.*lbf }

    Text in Illustration 
    V100135
    Rear



    F050151E02
  1. Using a chisel and hammer, stake the lock nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Securely stake the shaft to the lock nut groove.
    2. Be careful not to damage the parts around the lock nut.
    3. Do not apply excessive force to the shaft.



9. INSTALL PROPELLER SHAFT ASSEMBLY
(Click here)


10. ADD TRANSFER OIL
  1. Remove the filler plug and gasket.

  1. Add transfer oil so that the oil level is between 0 to 5.0 mm (0 to 0.196 in.) from the bottom lip of the filler plug hole.

    NOTICE:
    1. Add transfer oil slowly.
    2. Add transfer oil a little at a time, waiting several minutes between each addition of transfer oil.

    HINT:
    1. Viscosity:
      SAE 75W

      Capacity:
      1.0 liters (1.1 US qts, 0.9 lmp.qts)

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket to the filler plug and then tighten the plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



11. CHECK FOR TRANSFER OIL LEAK