Home › Drivetrain ยท VF2A TRANSFER / 4WD / AWD › TRANSFER CASE REAR OIL SEAL

TRANSFER CASE REAR OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN TRANSFER OIL


C216678
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the transfer oil.



2. REMOVE REAR PROPELLER SHAFT ASSEMBLY
  1. Remove the rear propeller shaft (Click here).



3. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Using a chisel and hammer, loosen the staked part of the lock nut.



    C216680E01
  1. Using SST to hold the companion flange, remove the lock nut.

    SST
    09330-00021  



    C217502E01
  1. Using SST, remove the companion flange.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



4. REMOVE REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.



5. REMOVE TRANSFER CASE REAR OIL SEAL


F043484E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil seal and rear case contact surface.



6. INSTALL TRANSFER CASE REAR OIL SEAL


F043486E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the case upper surface.

    SST
    09223-46011  
    09631-32020  



7. INSTALL REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL


F043517E02
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the companion flange.



8. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


C217367E01
  1. Apply gear oil to the connecting areas of the companion flange and output shaft.

  1. Install the companion flange to the output shaft.

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  

    Torque:
    118 N*m{ 1203 kgf*cm , 87 ft.*lbf }



    F050151E02
  1. Using a chisel and hammer, stake the lock nut.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Securely stake the shaft to the lock nut groove.
    2. Be careful not to damage parts around the lock nut.
    3. Do not apply excessive force to the shaft.



9. INSTALL PROPELLER SHAFT ASSEMBLY
  1. Install the rear propeller shaft (Click here).



10. ADD TRANSFER OIL


    C217364
  1. Remove the filler plug and gasket.

  1. Add oil so that the oil level is between 0 to 5.0 mm (0 to 0.196 in.) from the bottom lip of the filler plug hole.

    NOTICE:
    1. Add oil slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

    HINT:
    1. Viscosity:
      SAE 75W

      Capacity:
      1.0 liters (1.1 US qts, 0.9 lmp.qts)

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket to the filler plug and then tighten the plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



11. CHECK FOR TRANSFER OIL LEAK