Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR

BACK DOOR > DISASSEMBLY

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE DOOR PULL HANDLE


    B240249E01
  1. Using moulding remover, detach the 4 claws to remove the door pull handle.
    Text in Illustration 
    *1
    Moulding Remover

    HINT:
    Use the same procedure for all door pull handles.



3. REMOVE BACK DOOR LOCK PROTECTOR SUB-ASSEMBLY


    B240228
  1. Detach the 2 claws to remove the back door lock protector sub-assembly.



4. REMOVE ASSIST STRAP HOLE COVER


    B326929
  1. Detach the 2 claws and guide to remove the assist strap hole cover.



5. REMOVE ASSIST STRAP ASSEMBLY


    B326930
  1. Remove the bolt and assist strap assembly.



6. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    B240234
  1. Detach the 12 clips by pulling the back door trim panel assembly.



7. REMOVE BACK DOOR GLASS WEATHERSTRIP


    B240245
  1. Raise the 9 claws of the back door glass weatherstrip to remove the back door glass weatherstrip from the back door trim panel assembly as shown in the illustration.



8. REMOVE REAR NO. 2 SPEAKER ASSEMBLY
  1. Disconnect the connector.



    B240331
  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the speaker.

    NOTICE:
    Do not touch the cone of the speaker.



9. REMOVE MULTIPLEX NETWORK DOOR ECU


    B242092
  1. Disconnect the 3 connectors to detach the 2 clamps.



    B242093
  1. Remove the 3 screws.



    B242094
  1. Using a clip remover, detach the 2 clips to remove the multiplex network door ECU.



10. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER


    B240216
  1. Remove the No. 2 back door service hole cover.

    NOTICE:
    Remove any remaining tape on the back door side.



11. REMOVE BACK DOOR SERVICE HOLE COVER LH


    B240218
  1. Detach the clamp to move the wire harness out of the way.

  1. Remove the 5 screws.

  1. Using a clip remover, detach the 2 clips to remove the back door service hole cover LH.



12. REMOVE BACK DOOR SERVICE HOLE COVER RH


    B240219
  1. Detach the clamp to move the wire harness out of the way.

  1. Remove the 5 screws.

  1. Using a clip remover, detach the 2 clips to remove the back door service hole cover RH.



13. REMOVE BACK DOOR OUTSIDE MOULDING LH


B239981E01

NOTICE:
  1. Do not remove the clips.
  2. If the clips are damaged or fall off, replace them with new clips.

  1. Put protective tape around the back door outside moulding.

  1. Detach the 5 clips and remove the back door outside moulding.
    Text in Illustration 
    *1
    Protective Tape



14. REMOVE BACK DOOR OUTSIDE MOULDING RH

HINT:
Use the same procedure described for the LH side.



15. REMOVE REAR NO. 1 SPOILER COVER


B240307
  1. Detach the 4 clips and remove the rear No. 1 spoiler cover.



16. REMOVE REAR SPOILER SUB-ASSEMBLY


    B240308
  1. Remove the 4 grommets and 4 bolts.



    B240309E01
  1. Put protective tape around the rear spoiler.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector.

  1. Detach the 3 claws and remove the rear spoiler.



17. REMOVE REAR WIPER ARM


    E198997
  1. Remove the nut and rear wiper blade assembly.



18. REMOVE REAR WIPER MOTOR AND BRACKET ASSEMBLY


    E198998
  1. Disconnect the connector.

  1. Loosen the 3 bolts.

    NOTICE:
    Do not try to remove the bolts since they are integrated with the motor.

  1. Detach the 2 guides and remove the rear wiper motor



19. REMOVE NO. 1 BACK WINDOW WIPER MOTOR BRACKET


    E199085
  1. Remove the 3 bolts.

  1. Using a clip remover, detach the 2 clips to remove the No. 1 back window wiper motor bracket.



20. REMOVE REAR WASHER NOZZLE


    E199095
  1. Detach the 2 claws.



    E199096
  1. Disconnect the washer hose and remove the rear washer nozzle.



21. REMOVE REAR WIPER STOPPER


    E199086E01
  1. Insert a screwdriver into the rear spoiler service hole, detach the claw to remove the rear wiper stopper.
    Text in Illustration 
    *1
    Protective Tape



22. REMOVE BACK DOOR GLASS RUN


    B240220
  1. Remove the back door glass run.



23. REMOVE BACK DOOR GLASS
  1. Temporarily connect the multiplex network body ECU connectors.



    B240221
  1. Remove the hole plug.

  1. Connect the cable to the negative (-) battery terminal.



    B240222
  1. Move the back door glass until the 4 bolts can be seen through the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network body ECU connectors.



    B240223
  1. Remove the bolt to disconnect the 2 defogger connectors.



    B240222
  1. Remove the 4 bolts.



    B240225E01
  1. Remove the back door glass as shown in the illustration.

  1. Disconnect the rear window connector.

  1. Disconnect the multiplex network door ECU connector.



24. REMOVE OUTER BACK DOOR GLASS WEATHERSTRIP ASSEMBLY


B239982E01
  1. Put protective tape around the outer back door glass weatherstrip.
    Text in Illustration 
    *1
    Protective Tape

  1. Detach the 8 claws and remove the outer back door glass weatherstrip.



25. REMOVE BACK DOOR LOCK ASSEMBLY


    B240227
  1. Detach the 2 clamps and claw.



    B242011
  1. Disconnect the connector.

  1. Remove the 3 bolts and back door lock assembly.



26. REMOVE BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY


    B242097
  1. Disconnect the power window regulator motor assembly LH connector.



    B240229
  1. Remove the 5 bolts and back door power window regulator sub-assembly.

    HINT:
    Remove the back door power window regulator sub-assembly through the service hole.



27. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B240224
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.



28. REMOVE BACK DOOR LOCK CYLINDER (w/o Smart Key System)


    B240231
  1. Disconnect the connector.

  1. Remove the 2 nuts and back door lock cylinder.

    HINT:
    Remove the back door lock cylinder through the service hole.



29. REMOVE BACK DOOR OUTSIDE GARNISH


B239985
  1. Disconnect the connector.

  1. Remove the 4 nuts.

  1. Detach the 3 clips and remove the back door outside garnish.



30. REMOVE REAR TELEVISION CAMERA ASSEMBLY


    E198652
  1. Remove the 2 screws.



    E198651
  1. Disconnect the connector.

  1. Detach the 2 claws and remove the rear television camera assembly.



31. REMOVE BACK DOOR OPENER SWITCH ASSEMBLY


    B240243
  1. Disconnect the connector.

  1. Detach the guide.

  1. Remove the 2 screws and back door opener switch assembly.



32. REMOVE LICENSE PLATE LIGHT ASSEMBLY


    E199210E01
  1. Remove the 4 screws and light.



33. REMOVE BACK DOOR CONTROL SWITCH (w/ Smart Key System)


    B240246
  1. Remove the screw.

  1. Detach the claw and remove the back door control switch.



34. REMOVE BACK DOOR LOWER STOPPER


    B240241
  1. Remove the bolt.

  1. Detach the guide and back door lower stopper.

    HINT:
    Use the same procedure as for the LH side.



35. REMOVE BACK DOOR PANEL CUSHION


    B240230
  1. Detach the claw to remove the 2 back door panel cushions.



36. REMOVE BACK DOOR DAMPER STAY SUB-ASSEMBLY LH

NOTICE:
  1. Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing the vehicle.
  2. Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.
  3. In order to prevent the piston rod from deforming, do not apply any horizontal load to the door damper stay.



    B242503E01
  1. Using a screwdriver, remove the stop ring along the groove.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Release the ball joint and remove the back door damper stay sub-assembly.

    NOTICE:
    Remove the back door damper stay sub-assembly while supporting the back door by hand.



37. REMOVE BACK DOOR DAMPER STAY SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



38. REMOVE BACK DOOR STAY BOLT (for LH Side)


    B240247
  1. Remove the back door stay bolt.

    NOTICE:
    If the hood support is detached from the ball joint, it becomes non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



39. REMOVE BACK DOOR STAY BOLT (for RH Side)

HINT:
Use the same procedure as for the LH side.



40. REMOVE BACK DOOR UPPER DAMPER STAY BRACKET LH


    B240239
  1. Remove the 2 bolts and back door upper damper stay bracket.



41. REMOVE BACK DOOR UPPER DAMPER STAY BRACKET RH

HINT:
Use the same procedure as for the LH side.