Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR

BACK DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL BACK DOOR UPPER DAMPER STAY BRACKET LH


    B240239E01
  1. Install the back door upper damper stay bracket with the 2 bolts.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



2. INSTALL BACK DOOR UPPER DAMPER STAY BRACKET RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL BACK DOOR STAY BOLT (for LH Side)
  1. Clean the threaded portion on the vehicle body with a non-residue solvent.

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B240247
  1. Install the back door stay bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



4. INSTALL BACK DOOR STAY BOLT (for RH Side)

HINT:
Use the same procedure as for the LH side.



5. INSTALL BACK DOOR DAMPER STAY SUB-ASSEMBLY LH

NOTICE:
  1. Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing the vehicle.
  2. Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.
  3. In order to prevent the piston rod from deforming, do not apply any horizontal load to the door damper stay.



    B240240
  1. Install a new back door damper stay sub-assembly.

    NOTICE:
    1. Install the back door damper stay sub-assembly while supporting the back door by hand.
    2. Check that the back door stay assembly is attached to the ball joint and that the back door damper stay sub-assembly cannot be pulled out.



6. INSTALL BACK DOOR DAMPER STAY SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL BACK DOOR PANEL CUSHION


    B240230
  1. Attach the claw to install the 2 back door panel cushions.



8. INSTALL BACK DOOR LOWER STOPPER


    B240241
  1. Attach the guide to install the back door lower stopper with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure as for the LH side.



9. INSTALL BACK DOOR CONTROL SWITCH (w/ Smart Key System)


    B240246
  1. Attach the claw to install the back door control switch.

  1. Install the screw.



10. INSTALL LICENSE PLATE LIGHT ASSEMBLY
  1. Install the light with the 4 screws.



11. INSTALL BACK DOOR OPENER SWITCH ASSEMBLY


    B240243
  1. Install the back door opener switch assembly with the 2 screws.

  1. Attach the guide.

  1. Connect the connector.



12. INSTALL REAR TELEVISION CAMERA ASSEMBLY
  1. Attach the 2 claws to install the rear television camera assembly.

  1. Connect the connector.

  1. Install the 2 screws.



13. INSTALL BACK DOOR OUTSIDE GARNISH
  1. Attach the 3 clips to install the back door outside garnish.

  1. Install the 4 nuts.

  1. Connect the connector.



14. INSTALL BACK DOOR LOCK CYLINDER (w/o Smart Key System)


    B240231
  1. Install the back door lock cylinder with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



15. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B240224E01
  1. Using a T25 "TORX" socket wrench, install the back power window regulator motor assembly with the 3 screws.

    HINT:
    1. Tighten the screws in the order shown in the illustration.
    2. A new back door power window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are installed.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



16. INSTALL BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating parts of the back door power window regulator sub-assembly.



    B240229
  1. Install the back door power window regulator sub-assembly with the 5 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Do not drop the back door power window regulator sub-assembly as it may be damaged.



    B242097
  1. Connect the power window regulator motor assembly LH connector.



17. INSTALL BACK DOOR LOCK ASSEMBLY


    B242011
  1. Install the back door lock assembly with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the connector.



    B240227
  1. Attach the 2 clamps and claw.



18. INSTALL OUTER BACK DOOR GLASS WEATHERSTRIP ASSEMBLY
  1. Attach the 8 claws to install the outer back door glass weatherstrip.



19. INSTALL BACK DOOR GLASS
  1. Temporarily connect the multiplex network body ECU connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the back door glass until the bracket can be seen through the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network body ECU connectors.



    B240226E02
  1. Insert the back door glass as shown in the illustration.

    NOTICE:
    Do not damage the back door glass and back door panel.



    B240222
  1. Install the back door glass with the 4 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B240223
    B246228E01
  1. Connect the 2 defogger connectors and install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the SUS plate is bent, broken, etc., replace the wire harness.

    Text in Illustration 
    *1
    SUS Plate
    *2
    Wire Harness



    B240221
  1. Install the hole plug.



20. INSTALL BACK DOOR GLASS RUN


    B240220
  1. Install the back door glass run.



21. INSTALL REAR WIPER STOPPER


    E200707
  1. Attach the claw and guide to install the rear wiper stopper.



22. INSTALL REAR WASHER NOZZLE


    E199096
  1. Connect the washer hose.



    E199095
  1. Attach the 2 claws to install the rear washer nozzle.



23. INSTALL NO. 1 BACK WINDOW WIPER MOTOR BRACKET


    E199085
  1. Attach the 2 clips to install the No. 1 back window wiper motor bracket.

  1. Install the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



24. INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY


    E198998
  1. Attach the 2 guides and temporally install the rear wiper motor and bracket assembly with the 3 bolts.

  1. Tighten the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



25. INSTALL REAR WIPER ARM


    E199088E02
  1. Clean the wiper arm serrations.
    Text in Illustration 
    *1
    Wiper Arm Pivot Serrations



    E199087E01
  1. Clean the wiper pivot serrations with a wire brush.
    Text in Illustration 
    *1
    Wiper Pivot Serrations
    *2
    Wire Brush

  1. Operate the rear wiper and stop the rear wiper motor at the automatic stop position.

    HINT:
    The wiper motor does not operate if the back door and back door glass are not closed.



    E199089E01
  1. With the rear wiper blade and linear wiper step in the positions shown in the illustration, install the rear wiper blade assembly with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    Text in Illustration 
    *A
    Tightening Position
    *1
    Linear Wiper Step
    *2
    Wiper Blade Rubber Block
    *3
    Wiper Blade

    HINT:
    Hold the arm hinge down by hand while tightening the nut.



    E199090E01
  1. Place the rear wiper blade assembly in the automatic stop position.
    Text in Illustration 
    *A
    Rise-up Position
    *1
    Linear Wiper Step
    *2
    Wiper Blade Rubber Block
    *3
    Wiper Blade



26. INSTALL REAR SPOILER SUB-ASSEMBLY
  1. Attach the 3 claws to install the rear spoiler.

  1. Connect the connector.

  1. Install the 4 bolts and 4 grommets.



27. INSTALL REAR NO. 1 SPOILER COVER
  1. Attach the 4 clips to install the rear No. 1 spoiler cover.



28. INSTALL BACK DOOR OUTSIDE MOULDING LH
  1. Attach the 5 clips to install the back door outside moulding.



29. INSTALL BACK DOOR OUTSIDE MOULDING RH

HINT:
Use the same procedure described for the LH side.



30. INSTALL BACK DOOR SERVICE HOLE COVER LH


    B240218
  1. Attach the 2 clips to install the back door service hole cover LH.

  1. Install the 5 screws.

  1. Attach the clamp to install the wire harness.



31. INSTALL BACK DOOR SERVICE HOLE COVER RH


    B240219
  1. Attach the 2 clips to install the back door service hole cover RH.

  1. Install the 5 screws.

  1. Attach the clamp to install the wire harness.



32. INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the back door panel.



    B240232E01
  1. Install a new No. 2 back door service hole cover.
    Text in Illustration 
    *1
    Reference Point

  1. Attach the No. 2 back door service hole cover according to the reference points on the back door panel.

    NOTICE:
    Securely install the No. 2 back door service hole cover preventing wrinkles and air bubbles.



33. INSTALL MULTIPLEX NETWORK DOOR ECU


    B242094
  1. Attach the 2 clips to install the multiplex network door ECU to the door panel.



    B242093
  1. Install the 3 screws.



    B242092
  1. Connect the 3 connectors and attach the 2 clamps.



34. INSTALL REAR NO. 2 SPEAKER ASSEMBLY
  1. Temporarily install the speaker by attaching the 2 claws of the speaker to the door panel.

  1. Install the speaker with the 3 screws.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }

  1. Connect the connector.

    NOTICE:
    Do not touch the cone of the speaker.



35. INSTALL BACK DOOR GLASS WEATHERSTRIP


    B242125
  1. Install the back door glass weatherstrip on the back door trim panel assembly and fold down the 9 claws as shown in the illustration.



36. INSTALL BACK DOOR TRIM PANEL ASSEMBLY


    B240234
  1. Attach the 12 clips to install the back door trim panel assembly.



37. INSTALL ASSIST STRAP ASSEMBLY


    B326930
  1. Install the assist strap assembly with the bolt.



38. INSTALL ASSIST STRAP HOLE COVER


    B326929
  1. Attach the guide and 2 claws to install the assist strap hole cover.



39. INSTALL BACK DOOR LOCK PROTECTOR SUB-ASSEMBLY


    B240228
  1. Attach the 2 claws to install the back door lock protector sub-assembly.



40. INSTALL DOOR PULL HANDLE


    B357474
  1. Attach the 4 claws to install the door pull handle.

    HINT:
    Use the same procedure for all door pull handles.