Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Only Back Door cannot be Opened

for Preparation Click here


DESCRIPTION

When the back door is unlock and the multiplex network door ECU (back door P/W) receives the ON signal from the back door opener switch, it sends the signal to the main body ECU (multiplex network body ECU) which then activates the back door lock motor.

WIRING DIAGRAM


B241153E01


INSPECTION PROCEDURE

HINT:
Since the power door lock control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

1.READ VALUE USING TECHSTREAM (BACK DOOR OPENER SWITCH ASSEMBLY)
  1. Use the Data List to check if the back door opener switch is functioning properly (Click here).

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Handle Switch
    Back door opener switch signal / ON or OFF
    ON: Back door opener switch pushed
    OFF: Back door opener switch not pushed
    -

    OK:
    On tester screen, item changes between ON and OFF according to above chart.



NG
Go to step 6
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (BACK DOOR LOCK ASSEMBLY)
  1. Select the Active Test and check that the back door lock operates (Click here).

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Trunk and Back-Door Open
    Operate back door lock motor
    ON/OFF
    -

OK:
The back door lock motor operates normally.



NG
Go to step 4
OK


3.CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


  1. Measure the voltage according to the value(s) in the table below.


    B245666E01

    Standard Voltage:
    Tester Connection
    Tool Setting
    Switch Condition
    Specified Condition
    W10-24 (HSW+) - W10-7 (HSW-)
    5 V/DIV., 10 ms/DIV.
    Back door opener switch off
    Pulse generation (See waveform 1 or 2)



NG
REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.INSPECT BACK DOOR LOCK ASSEMBLY


    B241589
  1. Set the back door lock to the full-latch position.

  1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1 (ACT+)
    Battery negative (-) → 4 (ACT-)
    Moves to open-latch position

    Text in Illustration 
    V100135
    Full-latch
    V100136
    Open-latch



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the W8 back door lock connector.

  1. Disconnect the 2F main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W8-1 (ACT+) - 2F-9 (TR+)
    Always
    Below 1 Ω
    W8-4 (ACT-) - Body ground
    Always
    Below 1 Ω
    W8-1 (ACT+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

6.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY


    B241775E01
  1. Remove the back door opener switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UL) - 2 (E)
    Free
    10 kΩ or higher
    Pushed
    Below 1 Ω



NG
REPLACE BACK DOOR OPENER SWITCH ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)
  1. Disconnect the back door opener switch connector.

  1. Disconnect the W10 multiplex network door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W10-24 (HSW+) - W3-1 (UL)
    Always
    Below 1 Ω
    W10-7 (HSW-) - W3-2 (E)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) (Click here)