Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
(Click here)


2. REMOVE NO. 1 EMISSION CONTROL VALVE SET


    A225367
  1. Remove the 3 nuts and No. 1 emission control valve set.



3. REMOVE NO. 2 EMISSION CONTROL VALVE SET


    A225368
  1. Remove the 3 nuts and No. 2 emission control valve set.



4. REMOVE IGNITION COIL ASSEMBLY


    A224724
  1. Remove the 6 bolts and 6 ignition coils.



5. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A222114
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



6. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A223013
  1. Disconnect the 2 hoses.

  1. Remove the 3 bolts and water by-pass pipe sub-assembly.



7. REMOVE WATER INLET HOUSING


    A225380
  1. Disconnect the 3 water by-pass hoses.



    A223012
  1. Remove the 5 bolts and water inlet housing.



    A224736
  1. Remove the O-ring and gasket from the water outlet pipe and water pump assembly.



    A225379
  1. Remove the 3 water by-pass hoses.



8. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A158544
  1. Remove the bolt and No. 1 idler pulley sub-assembly.



9. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


A223006
  1. for Separate Type:
    Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulley sub-assemblies and 2 No. 2 idler pulley cover plates.

  1. for Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulley sub-assemblies.



10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A222180
  1. Remove the 5 bolts and V-ribbed belt tensioner assembly.



11. REMOVE OIL FILTER BRACKET


    A225410
  1. Remove the 2 nuts, bolt, oil filter bracket and gasket.



12. REMOVE CRANKSHAFT PULLEY


    A072947E04
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E02
  1. Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



13. REMOVE NO. 1 OIL PIPE


    A223691
  1. Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



14. REMOVE NO. 2 OIL PIPE


    A223692
  1. Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



15. REMOVE REAR CYLINDER HEAD COVER


    A224695
  1. Remove the 3 bolts and cover.



16. DISCONNECT FUEL PIPE SUB-ASSEMBLY
  1. Remove the 2 bolts and disconnect the fuel pipe sub-assembly.



17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A223666
  1. Remove the 12 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A223665
  1. Remove the 3 gaskets.



18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A223669
  1. Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A223668
  1. Remove the 3 gaskets.



19. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A174340
  1. Remove the 10 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A174341E02
  1. Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
    Text in Illustration 
    *1
    Oil Pan Seal Cutter

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.



20. REMOVE OIL STRAINER SUB-ASSEMBLY


    A221166
  1. Remove the 2 nuts, oil strainer sub-assembly and gasket.



21. REMOVE OIL PAN SUB-ASSEMBLY


    A222173
  1. Remove the 17 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A221168E01
  1. Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block as shown in the illustration.
    Text in Illustration 
    *1
    LH Side
    *2
    RH Side
    *a
    Pry

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.



    A222122
  1. Remove the 3 O-rings from the timing chain cover sub-assembly.



22. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A221169
  1. Remove the 26 bolts and the 2 nuts.



    A221170
  1. Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover sub-assembly, cylinder block and cylinder head.



    A221404
  1. Remove the oil pump gasket from the cylinder block.



23. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Using a screwdriver and wooden block, pry out the front crankshaft oil seal.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.