Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor while the engine speed is approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



2. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.



    A225432
  1. Remove the 8 bolts and hood sub-assembly.

    NOTICE:
    If the hood support is detached from the ball joint, it becomes non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)


6. REMOVE COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)


    B353485
  1. Remove the 4 clips and cool air intake duct.



7. REMOVE FRONT LOWER BUMPER COVER (w/o Intuitive Parking Assist System)
  1. Remove the clip, 5 bolts and front lower bumper cover.



8. REMOVE FRONT LOWER BUMPER COVER (w/ Intuitive Parking Assist System)
  1. Remove the clip, 4 bolts and front lower bumper cover.



9. REMOVE AIR INTAKE DUCT LH (w/ Intuitive Parking Assist System)


    B353484
  1. Remove the clip and bolt.

  1. Remove the 2 screws and air intake duct LH.



10. REMOVE AIR INTAKE DUCT RH (w/ Intuitive Parking Assist System)

HINT:
Use the same procedure as for the LH side.



11. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.



    A224743
  1. Unhook the No. 1 engine under cover sub-assembly from the vehicle body as shown in the illustration.



12. REMOVE TRANSMISSION UNDER COVER
  1. Remove the 2 bolts and transmission under cover.



13. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover assembly.



14. REMOVE FRONT FENDER APRON SEAL LH
  1. w/o KDSS:

    1. Remove the 5 clips and front fender apron seal LH.

  1. w/ KDSS:

    1. Remove the 7 clips and front fender apron seal LH.



15. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 4 clips and front fender apron seal RH.



16. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH
  1. Remove the 5 clips and front No. 1 fender apron to frame seal LH.



17. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Remove the 5 clips and front No. 1 fender apron to frame seal RH.



18. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.



19. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



20. DRAIN ENGINE COOLANT


CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



A273797E01


Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug (RH side)
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.



21. DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL


22. REMOVE BATTERY HOLD DOWN CLAMP


    A223416
  1. Loosen the 2 nuts and remove the battery clamp.



23. REMOVE BATTERY


24. REMOVE BATTERY TRAY


25. REMOVE V-BANK COVER


    A229925E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then detach the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



26. REMOVE FRONT BUMPER COVER
w/o Intuitive Parking Assist System: (Click here)
w/ Intuitive Parking Assist System: (Click here)


27. REMOVE AIR CLEANER CAP AND HOSE


    A224721
  1. Remove the air cleaner cap and hose.

    1. Disconnect the mass air flow meter connector, vacuum hose and ventilation hose and detach the 4 clamps.

    2. Loosen the clamp.

    3. Unfasten the 4 hook clamps, and then remove the bolt and air cleaner cap and hose.



28. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.



    A224715
  1. Detach the wire harness clamp.

  1. Remove the 3 bolts and air cleaner case sub-assembly.



29. REMOVE UPPER FRONT BUMPER RETAINER


    A311025
  1. Remove the 3 bolts, 2 screws and upper front bumper retainer.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Screw



30. REMOVE RADIATOR SIDE DEFLECTOR RH


    A311026
  1. Using a clip remover, detach the 3 claws and remove the clip. Then move the radiator side deflector RH so that the radiator can be removed in the step below.



31. REMOVE RADIATOR SIDE DEFLECTOR LH


    A311027
  1. Using a clip remover, detach the 3 claws and remove the clip. Then move the radiator side deflector LH so that the radiator can be removed in the step below.



32. REMOVE NO. 1 RADIATOR HOSE


    A223076
  1. Loosen the 2 clamps and remove the No. 1 radiator hose.



33. REMOVE NO. 2 RADIATOR HOSE


    A223077
  1. Loosen the clamp and disconnect the No. 2 radiator hose from the water inlet.



    A306025
  1. Detach the clamp from the fan shroud.

  1. Loosen the clamp and remove the No. 2 radiator hose.



34. REMOVE RADIATOR RESERVOIR TANK


    A223079
  1. Disconnect the reservoir hose from the upper side of the radiator tank.

  1. Remove the 3 bolts and radiator reservoir tank.



35. DISCONNECT OIL COOLER TUBE


    A223080
  1. Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.



36. REMOVE FAN SHROUD


    A223082
  1. Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan with fluid coupling and generator V-belt (Click here).



    A223083
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



37. REMOVE RADIATOR ASSEMBLY


    A224905
  1. Slide the 2 clamps and disconnect the 2 oil cooler hoses.



    A224957
  1. Remove the 4 bolts and radiator.



38. REMOVE AIR TUBE ASSEMBLY


  1. for Bank 1 Side:



      A221459
    1. Remove the bolt and disconnect the air tube assembly from the No. 1 emission control valve set.



  1. for Bank 2 Side:



      A221458
    1. Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.



39. REMOVE INTAKE AIR SURGE TANK


    A221456
  1. Disconnect the throttle body connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.



    A221457
  1. Disconnect the No. 1 fuel vapor feed hose.

  1. Disconnect the No. 1 vacuum switching valve connector.

  1. Disconnect the No. 1 ventilation hose.



    A221464
  1. Detach the 2 heater hose clamps.



    A221460
  1. Remove the 2 bolts and throttle body bracket.



    A225628
  1. Using a clip remover, detach the wire harness clamp.



    A221462
  1. Remove the 2 bolts and No. 1 surge tank stay.



    A221463
  1. Remove the 2 bolts and No. 2 surge tank stay.



    A221465
  1. Remove the 2 nuts, 4 bolts and intake air surge tank.

  1. Remove the gasket.



40. DISCONNECT VANE PUMP ASSEMBLY


    A223016
  1. Disconnect the 2 connectors.

  1. Detach the 2 wire harness clamps.



    A223015
  1. Remove the 2 bolts and disconnect the vane pump assembly.



41. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY


    E199372
  1. Remove the bolt and disconnect the discharge hose from the cooler compressor.

  1. Remove the O-ring from the discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



42. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E199373
  1. Remove the 2 bolts and disconnect the suction hose from the cooler compressor.

  1. Remove the O-ring from the suction hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



43. REMOVE COOLER COMPRESSOR ASSEMBLY


    E195719
  1. Disconnect the connector.

  1. Remove the 3 bolts and nut.

  1. Remove the stud bolt and cooler compressor.



44. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


45. REMOVE MANIFOLD STAY


    A222091
  1. Remove the 3 bolts and manifold stay.



46. REMOVE AIR TUBE


    A288445
  1. Remove the 2 bolts, 2 nuts and air tube.

  1. Remove the 2 gaskets from the air tube.

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.



47. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A222188
  1. Remove the 3 bolts and No. 1 exhaust manifold heat insulator.



48. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A222089
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 6 nuts, exhaust manifold sub-assembly RH and gasket.



49. REMOVE NO. 2 MANIFOLD STAY


    A221486
  1. Remove the 3 bolts and No. 2 manifold stay.



50. REMOVE NO. 2 AIR TUBE


    A288449
  1. Remove the 2 bolts, 2 nuts and No. 2 air tube.

  1. Remove the 2 gaskets from the No. 2 air tube.

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.



51. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A289304
  1. Remove the 3 bolts and No. 2 exhaust manifold heat insulator.



52. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A222092
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 6 nuts, exhaust manifold sub-assembly LH and gasket.



53. REMOVE WIRING HARNESS CLAMP BRACKET


    A222903
  1. Detach the clamp.

  1. Remove the bolt and wiring harness clamp bracket.



54. REMOVE GENERATOR ASSEMBLY


    A222881
  1. Open the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.



    A222884
  1. Remove the 2 bolts and disconnect the wire harness.



    A222882
  1. Disconnect the wire harness clamp.

  1. Remove the bolt and disconnect the generator bracket.



    A222883
  1. Remove the 2 bolts and generator assembly.



    A222885
  1. Remove the bolt and generator bracket.



55. REMOVE STARTER COVER


    A222904
  1. Remove the 3 bolts and starter cover.



56. REMOVE STARTER ASSEMBLY


    A222905
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the starter connector.

  1. Open the terminal cap.

  1. Remove the nut and bolt, and then disconnect the starter wire.



    A218197
  1. Remove the 2 bolts and starter.



57. REMOVE FLYWHEEL HOUSING SIDE COVER


A222907


58. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


59. DISCONNECT ENGINE WIRE


    A222166
  1. Remove the bolt and disconnect the connector.



    A222168
  1. for 4WD:

    1. Disconnect the connector and detach the clamp.



  1. Disconnect the ECM connector.



      A227938
    1. Detach the clamp and disconnect the 6 connectors.



    2. A223850
    3. Detach the grommet from the wire harness support.



    4. A223851
    5. Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.



60. DISCONNECT HEATER WATER HOSE ASSEMBLY


    A225434
  1. Disconnect the 2 hoses and heater water hose assembly.



61. DISCONNECT NO. 1 AND NO. 2 FUEL PIPES


    A225391E01
  1. Remove the No. 2 fuel pipe clamp from the fuel tube connector.
    Text in Illustration 
    *1
    No. 2 Fuel Pipe Clamp

  1. Disconnect the No. 1 and No. 2 fuel pipes (Click here).



62. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)


    C098708E07
  1. Place matchmarks on the propeller shaft flange and differential.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts and 4 bolts.



    C098709E07
  1. Place matchmarks on the propeller shaft flange and transfer flange.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 washers and front propeller shaft assembly.



63. REMOVE PROPELLER SHAFT ASSEMBLY (for 2WD)


    C098700E07
  1. Place matchmarks on the propeller shaft flange and differential flange.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 bolts and 4 washers.



    C098710E02
  1. Remove the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



64. REMOVE PROPELLER SHAFT ASSEMBLY (for 4WD)


    C098699E06
  1. Place matchmarks on the propeller shaft flange and transfer flange.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 washers and propeller shaft assembly.



    C098700E06
  1. Place matchmarks on the propeller shaft flange and differential flange.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 nuts, 4 bolts and 4 washers.



65. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
for 2WD: (Click here)
for 4WD: (Click here)


66. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A224775E01
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A224777
  1. Remove the 8 bolts, rear spacer, drive plate and ring gear sub-assembly and front spacer.



67. REMOVE ENGINE ASSEMBLY


    A229669E01
  1. Install 2 engine hangers with 4 bolts as shown in the illustration.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    No. 1 Engine Hanger
    12281-31110
    No. 2 Engine Hanger
    12282-31140
    Bolt
    91671-C0830

  1. Attach an engine sling device and hang the engine with a chain block.



    A225433
  1. Remove the 6 nuts and 4 bolts from the front engine mounting insulator LH and front engine mounting insulator RH.

  1. Lift the engine out of the vehicle carefully.

    NOTICE:
    Make sure the engine is clear of all wiring and hoses.

  1. Remove the front engine mounting insulator LH and front engine mounting insulator RH.

  1. Place the engine onto a work bench.



68. INSTALL ENGINE STAND
  1. Install the engine onto an engine stand with bolts.