Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B235899E01

  1. Remove the main body ECU (Click here).

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Install the main body ECU (Click here).



  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F9-3 (HAZ) - 2B-4 (GND1)
    W - W-B
    Hazard warning signal light signal input
    Hazard warning signal switch on
    Below 1 V
    Hazard warning signal switch off
    11 to 14 V
    F9-5 (HU) - 2B-4 (GND1)
    LG - W-B
    Headlight dimmer switch high signal input
    Headlight dimmer switch in high
    Below 1 V
    Headlight dimmer switch in low
    11 to 14 V
    F9-8 (HF) - 2B-4 (GND1)
    V - W-B
    Headlight dimmer switch high flash signal input
    Headlight dimmer switch in high flash position
    Below 1 V
    Headlight dimmer switch not in high flash position
    11 to 14 V
    F9-20 (CLTB) - 2B-4 (GND1)*
    P - W-B
    Automatic light control sensor power supply output
    Ignition switch off
    Below 1 V
    Ignition switch ON and headlight dimmer switch in AUTO position
    11 to 14 V
    F9-21 (CLTS) - 2B-4 (GND1)*
    R - W-B
    Automatic light control sensor signal input
    Ignition switch off
    Below 1 V
    Automatic light control system operates
    Pulse generation
    (See waveform 1)
    F9-27 (FFOG) - 2B-4 (GND1)
    L - W-B
    Front fog light switch input
    Front fog light switch on
    Below 1 V
    Front fog light switch off
    11 to 14 V
    F9-28 (A) - 2B-4 (GND1)*
    W - W-B
    Headlight dimmer switch AUTO signal input
    Headlight dimmer switch in AUTO
    Below 1 V
    Headlight dimmer switch not in AUTO
    11 to 14 V
    F9-29 (HEAD) - 2B-4 (GND1)
    SB - W-B
    Headlight dimmer switch head signal input
    Headlight dimmer switch in head
    Below 1 V
    Headlight dimmer switch not in head
    11 to 14 V
    F9-30 (TAIL) - 2B-4 (GND1)
    R - W-B
    Headlight dimmer switch tail signal input
    Headlight dimmer switch in tail or head
    Below 1 V
    Headlight dimmer switch in neither tail nor head
    11 to 14 V
    2D-7 (TRLY) - 2B-4 (GND1)
    G - W-B
    Clearance light signal output
    Headlight dimmer switch in tail position
    11 to 14 V
    Headlight dimmer switch not in tail position
    Below 1 V
    2D-9 (FFGO) - 2B-4 (GND1)
    W - W-B
    Front fog light signal output
    Headlight dimmer switch in tail and front fog light switch on
    Below 1 V
    Front fog light switch off
    11 to 14 V
    2D-24 (DIM) - 2B-4 (GND1)
    P - W-B
    H-LP HI relay drive output
    Headlight dimmer switch in high or high flash
    Below 1 V
    Headlight dimmer switch not in high or high flash
    11 to 14 V
    2D-40 (HRLY) - 2B-4 (GND1)
    P - W-B
    H-LP LO relay drive output
    Headlight dimmer switch in head
    Below 1 V
    Headlight dimmer switch not in head
    11 to 14 V
    2E-1 (TRLY) - 2B-4 (GND1)
    W - W-B
    Battery power supply
    Always
    11 to 14 V
    2F-16 (TRLY) - 2B-4 (GND1)
    G - W-B
    Taillight and license plate light signal output
    Headlight dimmer switch in tail position
    11 to 14 V
    Headlight dimmer switch not in tail position
    Below 1 V
    2F-27 (FLCY) - 2B-4 (GND1)
    R - W-B
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V

    1. *: w/ Automatic Light Control System
    If the result is not as specified, the main body ECU may have a malfunction.



      B113714E01
    1. Waveform 1
      Item
      Content
      Terminal No. (Symbol)
      F9-21 (CLTS) - 2B-4 (GND1)
      Tool setting
      5 V/DIV., 5 ms./DIV.
      Condition
      Ignition switch ON
      Headlight dimmer switch AUTO
      Automatic light control sensor with a hand → Automatic light control sensor covered exposed to ambient light

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.