Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY

FRONT SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
  1. Align the anchor plate positioning hole with the claw and install the anchor plate with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    First install the lower bolt, and then install the upper bolt.



2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


B239045E01

NOTICE:
When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.

  1. Align the seat belt retractor positioning holes with the claws of the vehicle.

  1. Install the seat belt with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    B241715
  1. Connect the pretensioner connector.

  1. Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL CENTER PILLAR GARNISH LH
  1. Pass the front seat outer belt floor anchor through the center pillar garnish LH.

  1. Attach the 2 clips and 2 guides to install the center pillar garnish LH.

  1. Install the bolt.



4. INSTALL LOWER CENTER PILLAR GARNISH LH
  1. Attach the 4 claws and 2 clips to install the lower center pillar garnish.

  1. Install the front seat outer belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



5. INSTALL OUTER LAP BELT ANCHOR COVER
  1. Attach the 3 claws to install the outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other outer lap belt anchor cover.



6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B240010E01
  1. Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle to install the rear door opening trim weatherstrip LH as shown in the illustration.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Mark Position



7. INSTALL REAR DOOR SCUFF PLATE LH
  1. Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.



8. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
  1. Install the quarter scuff plate LH with the 2 bolts.



9. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
  1. Attach the 2 claws to install the rear No. 1 floor step cover.

    HINT:
    Use the same procedure for all the rear No. 1 floor step covers.



10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B240008E01
  1. Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle to install the front door opening trim weatherstrip LH as shown in the illustration.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Mark Position



11. INSTALL DOOR SCUFF PLATE ASSEMBLY LH
  1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly LH.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



13. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).