Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ELECTRICAL KEY OSCILLATOR (for Rear Floor)

ELECTRICAL KEY OSCILLATOR (for Rear Floor) > INSTALLATION

for Preparation Click here



1. INSTALL INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY


    B237299
  1. Attach the 2 claws to install the indoor No. 2 electrical key antenna.

  1. Connect the connector.

  1. Install the front floor carpet assembly.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. w/o Rear No. 2 Seat:

    1. Connect each connector.

    2. Pass the rear seatback lock control lever base through the deck trim side panel assembly RH.

    3. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly RH.

    4. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.

    5. Install the 3 bolts and screw.

    6. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear No. 2 Seat:

    1. Connect each connector.

    2. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.

    3. Install the 3 bolts and screw.

    4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    5. Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. w/o Rear No. 2 Seat:

    1. Pass the rear seatback lock control lever base through the deck trim side panel assembly LH.

    2. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly LH.

    3. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly LH.

    4. Install the 3 bolts and 2 screws.

    5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear No. 2 Seat:

    1. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly LH.

    2. Install the 3 bolts and 2 screws.

    3. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    4. Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



5. INSTALL FRONT DECK SIDE TRIM COVER LH
  1. Attach the 2 claws to install the front deck side trim cover LH.



6. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
  1. Push in the No. 1 luggage compartment trim hook to install it.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim hook.



8. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
  1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



9. INSTALL REAR FLOOR PAD (w/o Deck Board)
  1. Install the rear floor pad.



10. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)
  1. Attach the 4 claws to install the rear floor carpet assembly.



11. INSTALL REAR FLOOR CARPET ASSEMBLY
  1. Attach the 4 claws to install the rear floor carpet.



12. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
  1. Attach the 5 clips to install the rear floor mat rear support plate.



13. INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)
  1. Install the inner floor side rail sub-assembly with the 4 bolts.



14. INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 2 guides to install the deck board assembly.

  1. Install the 6 bolts.



15. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)
  1. Attach the 4 clips and 2 guides to install the luggage compartment side cover sub-assembly LH.



16. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:
Use the same procedure as for the LH side.



17. INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 3 clips to install the rear No. 2 floor board assembly.



18. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)
  1. Attach the 2 clips and 2 guides to install the No. 2 deck board sub-assembly.



19. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



20. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)
  1. Attach the clip to install the No. 1 deck board sub-assembly.



21. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)
  1. Install the luggage hold belt striker and No. 1 luggage compartment trim cover with the bolt.

  1. Attach the 4 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim cover.



22. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B240010E01
  1. Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle to install the rear door opening trim weatherstrip LH as shown in the illustration.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Mark Position



23. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



24. INSTALL REAR DOOR SCUFF PLATE LH
  1. Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.



25. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



26. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
  1. Install the quarter scuff plate LH with the 2 bolts.



27. INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.



28. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
  1. Attach the 2 claws to install the rear No. 1 floor step cover.

    HINT:
    Use the same procedure for all the rear No. 1 floor step covers.



29. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
  1. Install the rear No. 2 seat assembly (Click here).