DTC P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) |
DTC P0771 Shift Solenoid "E" Performance (Shift Solenoid Valve SR) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0746 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic). |
|
| P0771 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic). |
|
| Related DTCs | P0746: Shift solenoid valve SL1/Functional check P0771: Shift solenoid valve SR/Functional check |
| Required sensors/Components (Main) | Shift solenoid valve SL1 Shift solenoid valve SR |
| Required sensors/Components (Related) | Speed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | P0746 and P0771 OFF malfunction (A): 0.4 sec. P0746 and P0771 OFF malfunction (B) and (C): Immediately P0771 ON malfunction: 2 cycles |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not stored | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0128 (ECT (Engine Coolant Temperature) sensor circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 sec. or more |
| ECT | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| Transfer | HIGH |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.5% or more at 2000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Continuous time for ECM selecting 4th gear | 2 sec. or more |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Current ECM selected gear | 2nd |
| Last ECM selected gear | 1st |
| Throttle valve opening angle (During transition from 1st to 2nd gear) | 1.5% or more at 2000 rpm (Conditions vary with engine speed) |
| Turbine speed/Output speed | 0.93 or more, and 1.07 or less (This means actual gear is 4th) |
| Turbine speed/Output speed | Does not change as follows 0.93 or more, and 1.07 or less (This means actual gear is 4th) ↓ 0.65 or more, and 0.79 or less (This means actual gear is 5th) |
| Output record of ECM from 4th to 5th up-shift | Recorded |
| Turbine speed - Output speed x 1st gear ratio (NT - NO x 1st gear ratio) | 150 rpm or more |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (31 mph) or less. |
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th |
| Shift solenoid valve SL1 | OFF | OFF | OFF | OFF | ON |
| Shift solenoid valve SR | OFF | OFF | OFF | OFF | ON |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0746 AND P0771) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| A |
| P0746, P0771 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Remove the test plug from the transmission case and connect SST.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Measure the line pressure.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.INSPECT SHIFT SOLENOID VALVE SL1 |
![]() |
Remove shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
| Valve moves and makes operating noise |
| *a | Component without harness connected (Shift Solenoid Valve SL1) |
|
| ||||
| OK | |
| 4.INSPECT SHIFT SOLENOID VALVE SR |
![]() |
Remove shift solenoid valve SR.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid valve SR connector terminal - Shift solenoid valve SR body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
| Valve moves and makes operating noise |
| *a | Component without harness connected (Shift Solenoid Valve SR) |
|
| ||||
| OK | |
| 5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||