Home › Drivetrain ยท A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE CONSOLE BOX ASSEMBLY (for VF2A)
(Click here)


3. REMOVE NO. 1 SHIFT AND SELECT LEVER BOOT (for VF2A)


    C213732
  1. Remove the 4 screws and No. 1 shift and select lever boot.



4. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY (for VF2A)
  1. Fold back the transfer front drive shift boot.



    C213734
  1. Using needle-nose pliers, remove the snap ring and pull out the transfer high and low shift lever assembly.



5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.



    A224743
  1. Unhook the No. 1 engine under cover sub-assembly from the vehicle body as shown in the illustration.



6. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover assembly.



7. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 4 clips and front fender apron seal RH.



8. REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL RH
  1. Remove the 5 clips and front No. 1 fender apron to frame seal RH.



9. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



10. REMOVE TRANSFER CASE LOWER PROTECTOR
  1. Remove the 4 bolts and transfer case lower protector.



11. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


12. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)


13. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


14. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C214587
  1. Remove the nut and clip, and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.



15. DISCONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE


    C213421E05
  1. Remove the 2 bolts to disconnect the 2 clamps.

  1. Using a union nut wrench, disconnect the No. 1 inlet oil cooler tube and No. 1 outlet oil cooler tube from each oil cooler tube union.



16. REMOVE MANIFOLD STAY


    C171485
  1. Remove the 3 bolts and the manifold stay.



17. REMOVE NO. 2 MANIFOLD STAY


    C171486
  1. Remove the 3 bolts and the No. 2 manifold stay.



18. REMOVE STARTER ASSEMBLY
(Click here)


19. REMOVE FLYWHEEL HOUSING SIDE COVER


    C157016E01
  1. Remove the flywheel housing side cover.



20. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT


    C157017E01
  1. Turn the crankshaft to gain access to the 6 drive plate and torque converter setting bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.



21. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C159641
  1. Support the automatic transmission assembly with a transmission jack. Lift the automatic transmission assembly slightly from the crossmember.



22. REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH (for X-Runner)


    C214435
  1. Remove the 8 bolts and front suspension member bracket LH and RH.



23. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    C171489
  1. Remove the 4 bolts of the rear No. 1 engine mounting insulator.



    C214464
  1. Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.

    HINT:
    Hold the bolts and loosen the nuts.



24. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


C214463
  1. Remove the bolt and rear engine mounting heat insulator.

  1. Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission assembly.



25. DISCONNECT WIRE HARNESS AND CONNECTOR


C214940
  1. Remove the nut and disconnect the ground cable.



    C157274
  1. Tilt the automatic transmission assembly downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



  1. for VF4BM:



    1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connectors.

      HINT:
      Detach the claw, press down the lever, and then disconnect the transmission wire connector.



      C218115E01

    2. Detach the 2 connector clamps and 7 harness clamps, and disconnect the wire harness.



  1. for VF2BM:



    1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors, transfer control side connector and 2 indicator switch connectors.

      HINT:
      Detach the claw, press down the lever, and then disconnect the transmission wire connector.



      C270511

    2. Detach the 2 connector clamps and 7 harness clamps, and disconnect the wire harness.



  1. for VF2A:



    1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and 3 transfer connectors.

      HINT:
      Detach the claw, press down the lever, and then disconnect the transmission wire connector.



      C217198E01

    2. Detach the 2 connector clamps and 5 harness clamps, and disconnect the wire harness.



26. DISCONNECT BREATHER HOSE


    C214459
  1. Disconnect the 3 breather hoses from the engine assembly.



27. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    C171497
  1. Remove the 9 bolts and automatic transmission assembly.

    NOTICE:
    Do not use excess force when prying the automatic transmission assembly.



28. REMOVE TRANSFER ASSEMBLY
  1. for VF4BM: (Click here)
  2. for VF2BM: (Click here)
  3. for VF2A: (Click here)


29. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    C111232
  1. Remove the 2 bolts and No. 1 transmission control cable bracket.



30. REMOVE TORQUE CONVERTER ASSEMBLY
  1. Remove the torque converter assembly from automatic transmission assembly.

    NOTICE:
    Remove the torque converter assembly horizontally from the input shaft.



31. INSPECT TORQUE CONVERTER ASSEMBLY
(Click here)