Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B240731
  1. Install the rear door inside locking cable assembly LH to the rear door lock assembly LH.



    B240730
  1. Attach the 3 claws to close the cover.



2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B240729
  1. Install the rear door lock remote control cable assembly LH to the rear door lock assembly LH.



    B240728
  1. Attach the claw to close the cover.



3. INSTALL REAR DOOR LOCK ASSEMBLY LH

NOTICE:
  1. When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wiring harness seal.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may allow water to enter into the connection. This may result in a malfunction of the rear door lock assembly.

  1. Apply MP grease to the sliding parts of the rear door lock assembly.

  1. Install a new door lock wiring harness seal to the rear door lock assembly.



    B239751
  1. Insert the rear door lock assembly into the rear door outside handle release plate, and set it in place on the rear door panel.

  1. Check that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 "TORX" wrench, install the rear door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the rear power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.



    B242781
  1. Operate the rear power window regulator switch assembly until the rear door window regulator sub-assembly LH reaches bottom dead center.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the rear power window regulator switch assembly.

  1. Install the front side of the rear door glass run LH.



    B242788E01
  1. Apply MP grease to the sliding areas of the rear door glass channel sub-assembly LH as shown in the illustration.
    Text in Illustration 
    *a
    5.0 mm (0.197 in.)
    *b
    157 mm (6.181 in.)
    *c
    5.0 mm (0.197 in.)
    V100155
    MP grease



    B240720
  1. Slide the rear door glass sub-assembly LH as shown in the illustration to install it.



5. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    B240718
  1. Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.



6. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    B240716E01
  1. Install the temporary bolt to the rear door window rear lower frame sub-assembly LH.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Temporarily install the rear door window rear lower frame sub-assembly LH to the rear door panel.

  1. Install the screw.

  1. Install the 2 bolts.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }

  1. Tighten the temporary bolt to install the rear door window rear lower frame sub-assembly LH.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



7. INSTALL REAR DOOR GLASS RUN LH


    B240715
  1. Install the rear door glass run LH.



8. INSTALL REAR DOOR SERVICE HOLE COVER LH
  1. Apply a new butyl tape to the rear door panel.



    B240712E01
  1. Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

  1. Install the rear door service hole cover LH according to the reference points on the rear door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the rear door service hole cover LH preventing wrinkles and air bubbles.

  1. Connect the connector.

  1. Attach the 3 clamps and rear door wire.



9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    B240749
  1. Attach the 3 claws to install the rear door inner glass weatherstrip LH as shown in the illustration.



10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240750
  1. Attach the claw to install the clamp.



    B242790
  1. Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.



    B242772
  1. Connect the connector.



    B357471E01
  1. Attach the rear door trim board sub-assembly LH to the 4 claws of the rear door inner glass weatherstrip LH as shown in the illustration.

  1. Attach the reference boss.
    Text in Illustration 
    *1
    Reference Boss



    B240704
  1. Attach the 9 clips to install the rear door trim board sub-assembly LH.

  1. Install the 3 screws.



    B357479
  1. Attach the 4 claws to install the 2 door armrest caps.



11. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH


    B357472
  1. Attach the 3 claws to install the rear door inside handle bezel LH.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).