Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives a door open/closed signal from each door courtesy light switch.

WIRING DIAGRAM


E284114E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (DOOR COURTESY LIGHT SWITCH)
  1. Using the Techstream, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal / ON or OFF
    ON: Rear door RH open
    OFF: Rear door RH closed
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal / ON or OFF
    ON: Rear door LH open
    OFF: Rear door LH closed
    -
    FR Door Courtesy SW
    Front door courtesy light switch RH signal / ON or OFF
    ON: Front door RH open
    OFF: Front door RH closed
    -
    FL Door Courtesy SW
    Front door courtesy light switch LH signal / ON or OFF
    ON: Front door LH open
    OFF: Front door LH closed
    -

    OK:
    Normal conditions listed above are displayed.

    Result 
    Result
    Proceed to
    OK
    A
    NG (Front door courtesy light switch does not operate)
    B
    NG (Rear door courtesy light switch does not operate)
    C



B
Go to step 2

C
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)


    E139234E30
  1. Remove the front door courtesy light switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Courtesy Light Switch Assembly)

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Pin not pushed
    Below 1 Ω
    Pin pushed
    10 kΩ or higher



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the O5*1 or N5*2 front door courtesy light switch assembly connector.

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for LH
    2. *2: for RH

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    O5-1 - 2F-27
    Always
    Below 1 Ω
    O5-1 - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    N5-1 - 2B-15
    Always
    Below 1 Ω
    N5-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY


  1. Remove the driver side junction block assembly (Click here).


    E284471E01


Text in Illustration 
*a
Component without harness connected
(Driver Side Junction Block Assembly)
-
-
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2F-27 - A-2 (FLCY)
    Always
    Below 1 Ω
    2B-15 - A-4 (FRCY)
    Always
    Below 1 Ω



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)


    E139234E30
  1. Remove the rear door courtesy light switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Component without harness connected
    (Rear Door Courtesy Light Switch Assembly)

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Pin not pushed
    Below 1 Ω
    Pin pushed
    10 kΩ or higher



NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the O6*1 or N7*2 rear door courtesy light switch assembly connector.

  1. Disconnect the F8 or F10 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for LH
    2. *2: for RH

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    O6-1 - F8-3 (LCTY)
    Always
    Below 1 Ω
    O6-1 - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    N7-1 - F10-27 (RCTY)
    Always
    Below 1 Ω
    N7-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)