Home › Drivetrain · VF4BM TRANSFER / 4WD / AWD › TRANSFER SYSTEM

TRANSFER SYSTEM > INSPECTION

for Preparation Click here



1. INSPECT INDICATOR LIGHT
  1. 4LO Indicator Light:

    1. Turn the ignition switch to ON.

    2. Move the shift lever to N (vehicle is stopped).

    3. Change the transfer position switch from H4L to L4L.

    4. Check the 4LO indicator light.

      OK:
      4LO indicator light comes on or 4LO indicator light comes on after blinking.

      If the result is not as specified, inspect the switch, four wheel drive control ECU and transfer shift actuator assembly. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (Click here). Then check the combination meter (Click here).

  1. Center Differential Lock Indicator Light:

    1. Turn the ignition switch to ON.

    2. Change the transfer position switch from H4F to H4L.

    3. Check the center differential lock indicator light.

      OK:
      Center differential lock indicator light comes on or Center differential lock indicator light comes on after blinking

      If the result is not as specified, inspect the switches, four wheel drive control ECU, transfer and shift actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (Click here). Then check the combination meter (Click here).



2. INSPECT 4 WHEEL DRIVE CONTROL ECU NO.2 (POWER SUPPLY)


    C217417E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F46-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Four Wheel Drive Control ECU)
    If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the four wheel drive control ECU (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F46-4 (GND) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, repair or replace the harness or connector.



3. INSPECT 4 WHEEL DRIVE CONTROL ECU NO.2 (TRANSFER POSITION SWITCH)


    C217417E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F47-11 (2-4) - Body ground
    Ignition switch ON
    Transfer position switch H4F
    Below 1.5 V
    Ignition switch ON
    Transfer position switch H4L
    Below 1.5 V
    Ignition switch ON
    Transfer position switch L4L
    10.5 to 14 V
    F47-13 (LO) - Body ground
    Ignition switch ON
    Transfer position switch H4F
    10.5 to 14 V
    Ignition switch ON
    Transfer position switch H4L
    Below 1.5 V
    Ignition switch ON
    Transfer position switch L4L
    Below 1.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Four Wheel Drive Control ECU)
    If the result is not as specified, check the power supply. If the power supply is normal, inspect the transfer position switch (Click here).



4. INSPECT MULTI MODE TRANSFER SHIFT ACTUATOR


  1. Check the harness and connector between four wheel drive control ECU and transfer shift actuator assembly (multi mode transfer shift actuator).

    1. Disconnect the B47 actuator connector.

    2. Disconnect the F47 and F46 ECU connectors.



    3. Measure the resistance according to the value(s) in the table below.


      C217418E01

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F47-7 (TL2) - B47-4 (TL2)
      Always
      Below 1 Ω
      F47-7 (TL2) - Body ground
      Always
      100 kΩ or higher
      F47-8 (TL3) - B47-5 (TL3)
      Always
      Below 1 Ω
      F47-8 (TL3) - Body ground
      Always
      100 kΩ or higher
      F47-14 (P1) - B47-9 (CDL)
      Always
      Below 1 Ω
      F47-14 (P1) - Body ground
      Always
      100 kΩ or higher
      F46-7 (TM2) - B47-1 (TM2)
      Always
      Below 1 Ω
      F46-7 (TM2) - Body ground
      Always
      100 kΩ or higher
      F46-8 (TM1) - B47-2 (TM1)
      Always
      Below 1 Ω
      F46-8 (TM1) - Body ground
      Always
      100 kΩ or higher
      B47-6 (GND) - Body ground
      Always
      Below 1 Ω


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)
      *b
      Front view of wire harness connector
      (to Transfer Shift Actuator Assembly)
      If the result is not as specified, repair or replace the harness or connector. If the harness or connector is normal, check the ECU output voltage.



  1. Check the four wheel drive control ECU (multi mode transfer shift actuator circuit).

    1. Connect the F47 and F46 ECU connectors.

    2. Connect the B47 actuator connector.



    3. C217417E03
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F46-8 (TM1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4F → H4L (During operation of multi mode transfer shift actuator motor from FREE to LOCK)
      10 to 14 V
      Ignition switch ON
      Transfer position switch H4F → H4L (Multi mode transfer shift actuator motor stopped)
      Below 1.5 V
      F46-7 (TM2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4L → H4F (During operation of multi mode transfer shift actuator motor from LOCK to FREE)
      10 to 14 V
      Ignition switch ON
      Transfer position switch H4L → H4F (Multi mode transfer shift actuator motor stopped)
      Below 1.5 V
      F47-7 (TL2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4L or L4L
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H4F
      10.5 to 14 V
      F47-8 (TL3) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4L or L4L
      10.5 to 14 V
      Ignition switch ON
      Transfer position switch H4F
      Below 1.5 V
      F47-14 (P1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4F
      9.5 to 14 V
      Ignition switch ON
      Transfer position switch H4L or L4L
      Below 1.5 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, determine if a malfunction is on the ECU side or actuator side by disconnecting the connector of the transfer shift actuator, and then check the ECU output voltage.



  1. Check the four wheel drive control ECU output voltage.

    1. Disconnect the B47 actuator connector.

    2. Connect the F47 and F46 ECU connectors.



    3. C217419E08
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      B47-9 (CDL) - B47-6 (GND1)
      Ignition switch ON
      9.5 to 14 V
      B47-4 (TL2) - B47-6 (GND1)
      Ignition switch ON
      10.5 to 14 V
      B47-5 (TL3) - B47-6 (GND1)
      Ignition switch ON
      10.5 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transfer Shift Actuator Assembly)
      If the result is not as specified, replace the four wheel drive control ECU (Click here). If the voltage is normal, inspect the multi mode transfer shift actuator, because the voltage applied to the motor cannot be measured.



  1. Inspect the multi mode transfer shift actuator (transfer shift actuator assembly).

    1. Remove the transfer shift actuator assembly (Click here).



    2. Check the LOCK to FREE switch.
      Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the LOCK to FREE position.

      NOTICE:
      1. Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.
      2. When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.

      HINT:
      When performing the operation described above, use the stop LP relay.



      C218269E04

      1. After the LOCK to FREE switch is complete, inspect the center differential lock detection switch and limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        4 (TL2) - 6 (GND1)
        After LOCK to FREE switch is complete
        0.5 MΩ or higher
        5 (TL3) - 6 (GND1)
        After LOCK to FREE switch is complete
        Below 12.5 Ω
        9 (CDL) - 10 (GND)
        After LOCK to FREE switch is complete
        0.5 MΩ or higher


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        LOCK to FREE



    3. Check the FREE to LOCK switch.
      Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the FREE to LOCK position.


      C218270E03

      1. After the FREE to LOCK switch is complete, inspect the center differential lock detection switch and limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        4 (TL2) - 6 (GND1)
        After FREE to LOCK switch is complete
        Below 12.5 Ω
        5 (TL3) - 6 (GND1)
        After FREE to LOCK switch is complete
        0.5 MΩ or higher
        9 (CDL) - 10 (GND)
        After FREE to LOCK switch is complete
        Below 12.5 Ω


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        FREE to LOCK
        If the result is not as specified, replace the transfer shift actuator assembly (Click here). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (Click here).



5. INSPECT HIGH-LOW TRANSFER SHIFT ACTUATOR


  1. Check the harness and connector between four wheel drive control ECU and transfer shift actuator (high-low transfer shift actuator).

    1. Disconnect the B47 actuator connector.

    2. Disconnect the F47 and F46 ECU connector.



    3. Measure the resistance according to the value(s) in the table below.


      C217418E02

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F47-1 (HL1) - B47-12 (HL1)
      Always
      Below 1 Ω
      F47-1 (HL1) - Body ground
      Always
      100 kΩ or higher
      F47-2 (HL2) - B47-11 (HL2)
      Always
      Below 1 Ω
      F47-2 (HL2) - Body ground
      Always
      100 kΩ or higher
      F46-2 (HM1) - B47-8 (HM1)
      Always
      Below 1 Ω
      F46-2 (HM1) - Body ground
      Always
      100 kΩ or higher
      F46-6 (HM2) - B47-7 (HM2)
      Always
      Below 1 Ω
      F46-6 (HM2) - Body ground
      Always
      100 kΩ or higher
      B47-10 (GND) - Body ground
      Always
      Below 1 Ω


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)
      *b
      Front view of wire harness connector
      (to Transfer Shift Actuator Assembly)
      If the result is not as specified, repair or replace the harness or connector. If the harness or connector is normal, check the ECU output voltage.



  1. Check the four wheel drive control ECU (high-low transfer shift actuator circuit).

    1. Connect the F47 and F46 ECU connectors.

    2. Connect the B47 actuator connector.



    3. C217417E04
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F46-6 (HM2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch L4L → H4L (During operation of high-low transfer shift actuator motor from LOW to HIGH)
      10 to 14 V
      Ignition switch ON
      Transfer position switch L4L → H4L (High-low transfer shift actuator motor stopped)
      Below 1.5 V
      F46-2 (HM1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4L → L4L (During operation of high-low transfer shift actuator motor from HIGH to LOW)
      10 to 14 V
      Ignition switch ON
      Transfer position switch H4L → L4L (High-low transfer shift actuator motor stopped)
      Below 1.5 V
      F47-1 (HL1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4F or H4L
      10.5 to 14 V
      Ignition switch ON
      Transfer position switch L4L
      Below 1.5 V
      F47-2 (HL2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4F or H4L
      Below 1.5 V
      Ignition switch ON
      Transfer position switch L4L
      10.5 to 14 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, determine if the malfunction is on the ECU side or actuator side by disconnecting the connector of the high-low transfer shift actuator, and then checking the ECU output voltage.



  1. Check the four wheel drive control ECU output voltage.

    1. Connect the F47 and F46 ECU connectors.

    2. Disconnect the B47 actuator connector.



    3. C217419E02
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      B47-11 (HL2) - B47-10 (GND)
      Ignition switch ON
      10.5 to 14 V
      B47-12 (HL1) - B47-10 (GND)
      Ignition switch ON
      10.5 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transfer Shift Actuator Assembly)
      If the result is not as specified, replace the four wheel drive control ECU (Click here). If the voltage is normal, inspect the high-low transfer shift actuator, because the voltage applied to the motor cannot be measured.



  1. Inspect the high-low transfer shift actuator transfer shift actuator assembly.

    1. Remove the transfer shift actuator assembly (Click here).



    2. Check the HIGH to LOW switch.
      Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the HIGH to LOW position.

      NOTICE:
      1. Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.
      2. When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.

      HINT:
      When performing the operation described above, use the stop LP relay.



      C218271E02

      1. After the HIGH to LOW switch is complete, inspect the limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        12 (HL1) - 10 (GND)
        After HIGH to LOW switch is complete
        Below 12.5 Ω
        11 (HL2) - 10 (GND)
        After HIGH to LOW switch is complete
        0.5 MΩ or higher


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        HIGH to LOW



    3. Check the LOW to HIGH switch.
      Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the LOW to HIGH position.


      C218272E02

      1. After the LOW to HIGH switch is complete, inspect the limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        12 (HL1) - 10 (GND)
        After LOW to HIGH switch is complete
        0.5 MΩ or higher
        11 (HL2) - 10 (GND)
        After LOW to HIGH switch is complete
        Below 12.5 Ω


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        LOW to HIGH
        If the result is not as specified, replace the transfer shift actuator assembly (Click here). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (Click here).