Home › Drivetrain · VF4BM TRANSFER / 4WD / AWD › 4WD CONTROL SWITCH

4WD CONTROL SWITCH > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT TRANSFER POSITION SWITCH


  1. Check the harness and connector (four wheel drive control ECU - battery and body ground).



      C217417E01
    1. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F46-3 (IG) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the four wheel drive control ECU (Click here).
      If there is a malfunction, repair or replace the harness or connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F46-4 (GND) - Body ground
      Always
      Below 1 Ω



  1. Check the harness and connector (transfer position switch - four wheel drive control ECU).

    1. Disconnect the F47 ECU connector.

    2. Disconnect the F73 switch connector.



    3. Measure the resistance according to the value(s) in the table below.


      C217432E01

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F73-5 (LO) - F47-13 (LO)
      Always
      Below 1 Ω
      F73-5 (LO) - Body ground
      Always
      100 kΩ or higher
      F73-3 (GND) - Body ground
      Always
      Below 1 Ω
      F73-1 (HI) - F47-11 (2-4)
      Always
      Below 1 Ω
      F73-1 (HI) - Body ground
      Always
      100 kΩ or higher


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transfer Position Switch)
      *b
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)
      If the result is not as specified, repair or replace the harness or connector.



  1. Check the transfer position switch.

    1. Turn the ignition switch off.

    2. Connect the F73 switch connector.

    3. Connect the F47 ECU connector.



    4. C217417E02
    5. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F47-11 (2-4) - Body ground
      Ignition switch ON
      Transfer position switch H4F
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H4L
      Below 1.5 V
      Ignition switch ON
      Transfer position switch L4L
      10.5 to 14 V
      F47-13 (LO) - Body ground
      Ignition switch ON
      Transfer position switch H4F
      10.5 to 14 V
      Ignition switch ON
      Transfer position switch H4L
      Below 1.5 V
      Ignition switch ON
      Transfer position switch L4L
      Below 1.5 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, check the four wheel drive control ECU.



  1. Check the four wheel drive control ECU.

    1. Disconnect the F73 switch connector.



    2. C217434E01
    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F73-1 (HI) - Body ground
      Ignition switch ON
      10.5 to 14 V
      F73-5 (LO) - Body ground
      Ignition switch ON
      10.5 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transfer Position Switch)
      If the voltage is not as specified, replace the four wheel drive control ECU (Click here). If the voltage is normal, replace the transfer position switch (Click here).