Home › Drivetrain · VF2BM TRANSFER / 4WD / AWD › 4WD CONTROL SWITCH

4WD CONTROL SWITCH > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT TRANSFER POSITION SWITCH


  1. Check the harness and connector (four wheel drive control ECU - battery and body ground).



      C217417E01
    1. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F46-3 (IG) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the four wheel drive control ECU (Click here).
      If there is a malfunction, repair or replace the harness or connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F46-4 (GND) - Body ground
      Always
      Below 1 Ω



  1. Check the harness and connector (transfer position switch - four wheel drive control ECU).

    1. Disconnect the F47 four wheel drive control ECU connector.

    2. Disconnect the F91 transfer position switch connector.



    3. Measure the resistance according to the value(s) in the table below.


      C217432E05


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transfer Position Switch)
      *b
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F91-5 (LO) - F47-13 (LO)
      Always
      Below 1 Ω
      F91-5 (LO) - Body ground
      Always
      100 kΩ or higher
      F91-3 (GND) - Body ground
      Always
      Below 1 Ω
      F91-1 (2-4) - F47-11 (2-4)
      Always
      Below 1 Ω
      F91-1 (2-4) - Body ground
      Always
      100 kΩ or higher

      If the result is not as specified, repair or replace the harness or connector.



  1. Check the transfer position switch.

    1. Turn the ignition switch off.

    2. Connect the F91 transfer position switch connector.

    3. Connect the F47 four wheel drive control ECU connector.



    4. C217417E02
    5. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F47-11 (2-4) - Body ground
      Ignition switch ON
      Transfer position switch H2
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H4
      Below 1.5 V
      Ignition switch ON
      Transfer position switch L4
      10.5 to 14 V
      F47-13 (LO) - Body ground
      Ignition switch ON
      Transfer position switch H2
      10.5 to 14 V
      Ignition switch ON
      Transfer position switch H4
      Below 1.5 V
      Ignition switch ON
      Transfer position switch L4
      Below 1.5 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, check the four wheel drive control ECU.



  1. Check the four wheel drive control ECU.

    1. Disconnect the F91 transfer position switch connector.



    2. C217434E05
    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F91-1 (2-4) - Body ground
      Ignition switch ON
      10.5 to 14 V
      F91-5 (LO) - Body ground
      Ignition switch ON
      10.5 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transfer Position Switch)

    4. Connect the F91 transfer position switch connector.
      If the voltage is not as specified, replace the four wheel drive control ECU (Click here). If the voltage is normal, replace the transfer position switch (Click here).