Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

DTC    C2126/26    Transmitter ID not Received in Main Mode

for Preparation Click here


DESCRIPTION

After all IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and the tire pressure warning light blinks for 1 minute and then comes on.
When the tire pressure warning ECU successfully receives information from all the transmitters whose IDs are stored in the ECU, DTC C2126/26 is cleared and the tire pressure warning light goes off.

DTC No.
DTC Detection Condition
Trouble Area
C2126/26
After ID registration is completed, the ECU does not receive information from transmitters whose IDs are stored in the ECU.
  1. ID registration failure
  2. Tire pressure warning valve and transmitter
  3. Tire pressure warning antenna and receiver
  4. Tire pressure warning ECU

HINT:
If the IDs stored in the tire pressure warning ECU differ from the transmitter IDs, DTC C2126/26 is stored. Check that the IDs in the ECU are the same as the transmitter IDs.


WIRING DIAGRAM

Refer to DTCs C2111/11, C2112/12, C2113/13 and C2114/14 .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using the Techstream and write them down before removal.
  2. It is necessary to perform registration of the transmitter IDs into the tire pressure warning ECU after the ECU and/or the tire pressure warning valve and transmitter has been replaced (Click here).

1.IDENTIFY TRANSMITTER NOT RECEIVED
  1. Set the tire pressure to the appropriate specified value (Click here).

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    *: It may take approximately 2 or 3 minutes until the values are displayed.

  1. Rapidly reduce the tire pressure of each tire by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

  1. Check the Data List.

    NOTICE:
    1. It takes approximately 2 or 3 minutes to display the updated tire pressure data.
    2. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.
    3. Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.

  1. After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID4) has changed, repeat this procedure for each tire. Identify the transmitter not received.
    Result 
    Result
    Proceed to
    One or more transmitters abnormal
    A
    All normal
    B



B
END
A


2.CHECK TRANSMITTER ID
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Registered ID1 Code
    Registered ID1 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID1 displayed
    *: Displayed only when the ID No. is not registered.
    Registered ID2 Code
    Registered ID2 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID2 displayed
    *: Displayed only when the ID No. is not registered.
    Registered ID3 Code
    Registered ID3 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID3 displayed
    *: Displayed only when the ID No. is not registered.
    Registered ID4 Code
    Registered ID4 code/
    min.: 0
    max.: FFFFFFF*
    ID No. registered in transmitter ID4 displayed
    *: Displayed only when the ID No. is not registered.

  1. Check the ID number on the identified transmitter by removing it from the tire and wheel.

  1. Confirm that the ID number on the transmitter and recorded transmitter ID match.
    Result 
    Result
    Proceed to
    Match
    A
    Do not match
    B



B
Go to step 4
A


3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
  1. Replace the tire pressure warning valve and transmitter .


NEXT


4.PERFORM REGISTRATION OF TRANSMITTER ID
  1. Perform registration (Click here).


NEXT


5.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    1. *: It may take approximately 2 or 3 minutes until the values are displayed.
    2. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.


    Result 
    Result
    Proceed to
    Tire pressure values are not displayed
    A
    All tire pressure readings are equal to specified values
    B



B
END
A


6.REPLACE TIRE PRESSURE WARNING ANTENNA AND RECEIVER
  1. Replace the tire pressure warning antenna and receiver (Click here).


NEXT


7.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    1. *: It may take approximately 2 or 3 minutes until the values are displayed.
    2. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.


    Result 
    Result
    Proceed to
    All tire pressure readings are equal to specified values
    A
    Tire pressure values are not displayed
    B



B
REPLACE TIRE PRESSURE WARNING ECU (Click here)
A

END