Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING

FRONT DOOR WINDOW FRAME MOULDING > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When installing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.

    Standard:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)
    Window Frame Moulding
    20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or window frame moulding excessively.



1. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new front door rear window frame moulding.

    1. Using a heat light, heat a new front door rear window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the front door rear window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the clip and double-sided tape to install the front door rear window frame moulding.

      HINT:
      Press the front door rear window frame moulding firmly to install it.

  1. Install a new door window frame moulding clip.



2. INSTALL FRONT DOOR WEATHERSTRIP LH
  1. Attach the 3 clips to install the upper part of the front door weatherstrip.



3. INSTALL FRONT DOOR BELT MOULDING LH
  1. Attach the 6 claws to install the front door belt moulding.



4. INSTALL FRONT DOOR GLASS RUN LH


    B240586
  1. Install the front door glass run LH.



5. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the multiplex network master switch assembly (for Driver Side).

  1. Connect the power window regulator switch assembly (for Front Passenger Side).

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly (for Driver Side).

  1. Disconnect the power window regulator switch assembly (for Front Passenger Side).



    B353492E01
  1. Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.



    B353480E01
  1. Install the front door glass sub-assembly LH with the 2 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
  1. Attach the claw to install the outer rear view mirror assembly LH.



    B354476E01
  1. Install the 3 nuts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Attach the clamp.

  1. Connect the connector.



7. INSTALL FRONT DOOR SERVICE HOLE COVER LH
  1. Apply a new butyl tape to the front door panel.



    B240610E01
  1. Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

  1. Install a new front door service hole cover LH according to the reference points on the front door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the front door service hole cover LH preventing wrinkles and air bubbles.



    B240582
  1. Attach the 2 clamps.

  1. Connect the door wire with the bolt.



8. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    B240611
  1. Attach the 4 claws to install the front door inner glass weatherstrip LH as shown in the illustration.



9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240612
  1. Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.



    B240574
  1. Connect the connector.



    B354466E01
  1. Attach the front door trim board sub-assembly LH to the 4 claws of the front door inner glass weatherstrip LH as shown in the illustration.

  1. Attach the reference boss.
    Text in Illustration 
    *1
    Reference Boss



    B353478
  1. Attach the 11 clips to install the front door trim board sub-assembly LH.

  1. Install the 3 screws.



    B353477
  1. Attach the 4 claws to install the 2 door armrest caps.



10. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    B357473
  1. Attach the 3 claws to install the No. 2 door inside handle bezel LH.



11. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B240255
  1. Attach the 2 clips to install the front door lower frame bracket garnish LH.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



13. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).