Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Front Door)

BLACK OUT TAPE (for Front Door) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When installing the window frame moulding, black out tape and outside stripe, heat the vehicle body, window frame moulding, black out tape and outside stripe using a heat light.

    Standard:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)
    Window Frame Moulding
    20 to 30°C (68 to 86°F)
    Black Out Tape
    20 to 30°C (68 to 86°F)
    Outside Stripe
    20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body, window frame moulding, black out tape or outside stripe excessively.



1. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature.

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.

  1. Before installation.

    1. Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape.

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

      NOTICE:
      Do not bend the tape or leave it in place with a high temperature.



  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

    NOTICE:
    1. Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit after removal.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.


      B233855E02


      Text in Illustration 
      *A
      Pressing
      *B
      Pulling
      *1
      Squeegee
      *2
      Black Out Tape
      *3
      Release Paper
      -
      -
      *a
      Sectional View
      *b
      Non-padded Side
      *c
      Padded Side
      -
      -

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.

      HINT:
      1. Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.



    B233856E02
  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

    1. If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

      Text in Illustration 
      *1
      Squeegee
      *a
      First
      *b
      Second
      *c
      Third

  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for the corners).

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles on the tape and achieve a neat finish.

  1. Check after installation.

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

      NOTICE:
      Do not reuse the tape.



2. INSTALL FRONT DOOR LOWER OUTSIDE STRIPE LH


B301229E01
  1. Refer to the illustration to position a new front door lower outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    +/- 1.0 mm (0.039 in.) From End



3. INSTALL FRONT DOOR OUTSIDE STRIPE LH


B301230E01
  1. Refer to the illustration to position a new front door outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    +/- 1.0 mm (0.039 in.) From End



4. INSTALL NO. 1 BLACK OUT TAPE LH


B242361E01
  1. Refer to the illustration to position new black out tape.

    Reference Value:
    Area
    Specified Condition
    A
    2 to 4 mm (0.078 to 0.158 in.)
    B
    4 to 6 mm (0.157 to 0.236 in.)



5. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new front door rear window frame moulding.

    1. Using a heat light, heat a new front door rear window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the front door rear window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the clip and double-sided tape to install the front door rear window frame moulding.

      HINT:
      Press the front door rear window frame moulding firmly to install it.

  1. Install a new door window frame moulding clip.



6. INSTALL FRONT DOOR WEATHERSTRIP LH
  1. Attach the 3 clips to install the upper part of the front door weatherstrip.



7. INSTALL FRONT DOOR BELT MOULDING LH
  1. Attach the 6 claws to install the front door belt moulding.



8. INSTALL FRONT DOOR GLASS RUN LH


    B240586
  1. Install the front door glass run LH.



9. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the multiplex network master switch assembly (for Driver Side).

  1. Connect the power window regulator switch assembly (for Front Passenger Side).

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly (for Driver Side).

  1. Disconnect the power window regulator switch assembly (for Front Passenger Side).



    B353492E01
  1. Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.



    B353480E01
  1. Install the front door glass sub-assembly LH with the 2 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



10. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
  1. Attach the claw to install the outer rear view mirror assembly LH.



    B354476E01
  1. Install the 3 nuts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Attach the clamp.

  1. Connect the connector.



11. INSTALL FRONT DOOR SERVICE HOLE COVER LH
  1. Apply a new butyl tape to the front door panel.



    B240610E01
  1. Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

  1. Install a new front door service hole cover LH according to the reference points on the front door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the front door service hole cover LH preventing wrinkles and air bubbles.



    B240582
  1. Attach the 2 clamps.

  1. Connect the door wire with the bolt.



12. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    B240611
  1. Attach the 4 claws to install the front door inner glass weatherstrip LH as shown in the illustration.



13. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240612
  1. Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.



    B240574
  1. Connect the connector.



    B354466E01
  1. Attach the front door trim board sub-assembly LH to the 4 claws of the front door inner glass weatherstrip LH as shown in the illustration.

  1. Attach the reference boss.
    Text in Illustration 
    *1
    Reference Boss



    B353478
  1. Attach the 11 clips to install the front door trim board sub-assembly LH.

  1. Install the 3 screws.



    B353477
  1. Attach the 4 claws to install the 2 door armrest caps.



14. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    B357473
  1. Attach the 3 claws to install the No. 2 door inside handle bezel LH.



15. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B240255
  1. Attach the 2 clips to install the front door lower frame bracket garnish LH.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some system need to be initialized after the cable is reconnected (Click here).



17. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).