Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B240601
  1. Install the front door inside locking cable assembly LH to the front door lock assembly LH.



    B240600
  1. Attach the 3 claws to close the cover.



2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B240599
  1. Install the front door lock remote control cable assembly LH to the front door lock assembly LH.



3. INSTALL FRONT DOOR LOCK ASSEMBLY LH


B239752

NOTICE:
  1. When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wiring harness seal.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may allow water to enter into the connection. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock assembly.

  1. Install a new door lock wiring harness seal to the front door lock assembly.

  1. Insert the front door lock open rod into the front door lock assembly.

  1. Check that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a T30 "TORX" wrench, install the front door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH


    B241225
  1. Attach the claw to install the front door outside handle cover LH to the lock cylinder assembly.



5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    B242327
  1. Install the front door rear lower frame sub-assembly LH with the bolt as shown in the illustration.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



6. INSTALL FRONT DOOR GLASS RUN LH


    B240586
  1. Install the front door glass run LH.



7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the multiplex network master switch assembly (for Driver Side).

  1. Connect the power window regulator switch assembly (for Front Passenger Side).

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly (for Driver Side).

  1. Disconnect the power window regulator switch assembly (for Front Passenger Side).



    B353492E01
  1. Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.



    B353480E01
  1. Install the front door glass sub-assembly LH with the 2 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



8. INSTALL FRONT DOOR SERVICE HOLE COVER LH
  1. Apply a new butyl tape to the front door panel.



    B240610E01
  1. Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

  1. Install a new front door service hole cover LH according to the reference points on the front door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the front door service hole cover LH preventing wrinkles and air bubbles.



    B240582
  1. Attach the 2 clamps.

  1. Connect the door wire with the bolt.



9. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    B240611
  1. Attach the 4 claws to install the front door inner glass weatherstrip LH as shown in the illustration.



10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240612
  1. Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.



    B240574
  1. Connect the connector.



    B354466E01
  1. Attach the front door trim board sub-assembly LH to the 4 claws of the front door inner glass weatherstrip LH as shown in the illustration.

  1. Attach the reference boss.
    Text in Illustration 
    *1
    Reference Boss



    B353478
  1. Attach the 11 clips to install the front door trim board sub-assembly LH.

  1. Install the 3 screws.



    B353477
  1. Attach the 4 claws to install the 2 door armrest caps.



11. INSTALL DOOR NO. 2 INSIDE HANDLE BEZEL LH


    B357473
  1. Attach the 3 claws to install the No. 2 door inside handle bezel LH.



12. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B240255
  1. Attach the 2 clips to install the front door lower frame bracket garnish LH.



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



14. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).