Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B240255
  1. Detach the 2 clips to remove the front door lower frame bracket garnish LH.



3. REMOVE DOOR NO. 2 INSIDE HANDLE BEZEL LH


    B240256E01
  1. Using a moulding remover, detach the 3 claws to remove the No. 2 door inside handle bezel LH as shown in the illustration.
    Text in Illustration 
    *1
    Moulding Remover



4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B353477
  1. Detach the 4 claws to remove the 2 door armrest caps.



    B353478
  1. Remove the 3 screws.

  1. Detach the 11 clips.



    B353479E01
  1. Pull out the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.

  1. Raise the front door trim board sub-assembly LH and detach the 4 claws and reference boss to remove the front door trim board sub-assembly LH together with the front door inner glass weatherstrip LH.
    Text in Illustration 
    *1
    Reference Boss



    B240574
  1. Disconnect the connector.



    B238525
  1. Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.



5. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    B238526
  1. Using a screwdriver, detach the 4 claws to remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH as shown in the illustration.



6. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    B240582
  1. Remove the bolt.

  1. Detach the 2 clamps and move the front door wire out of the way to remove the front door service hole cover LH.

    HINT:
    Remove any remaining butyl tape from the door panel.



7. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the multiplex network master switch assembly (for Driver Side).

  1. Connect the power window regulator switch assembly (for Front Passenger Side).

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly (for Driver Side).

  1. Disconnect the power window regulator switch assembly (for Front Passenger Side).



    B353480
  1. Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.



    B353481E01
  1. Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly LH.



8. REMOVE FRONT DOOR GLASS RUN LH


    B240586
  1. Remove the front door glass run LH.



9. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    B240587
  1. Remove the bolt and front door rear lower frame sub-assembly LH as shown in the illustration.



10. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    B238539
  1. Using a screwdriver, detach the claw to remove the front door outside handle cover LH from the lock cylinder assembly.

    HINT:
    Tape the screwdriver tip before use.



11. REMOVE FRONT DOOR LOCK ASSEMBLY LH
  1. Disconnect the connector.



    B237416
  1. Using a T30 "TORX" wrench, remove the 3 screws.

  1. Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.

  1. Remove the front door lock open rod from the front door lock assembly.

  1. Remove the door lock wiring harness seal from the front door lock assembly.



12. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B240599
  1. Remove the front door lock remote control cable assembly LH from the front door lock assembly LH.



13. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B240600
  1. Using a screwdriver, detach the 3 claws to open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B240601
  1. Remove the front door inside locking cable assembly LH from the front door lock assembly LH.