Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door)

BLACK OUT TAPE (for Rear Door) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. When installing the window frame moulding, black out tape and outside stripe, heat the vehicle body, window frame moulding, black out tape and outside stripe using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Window Frame Moulding
20 to 30°C (68 to 86°F)
Black Out Tape
20 to 30°C (68 to 86°F)
Outside Stripe
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body, window frame moulding, black out tape or outside stripe excessively.



1. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature.

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.

  1. Before installation.

    1. Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape.

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

      NOTICE:
      Do not bend the tape or leave it in place with a high temperature.



  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

    NOTICE:
    1. Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit after removal.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.


      B233855E02


      Text in Illustration 
      *A
      Pressing
      *B
      Pulling
      *1
      Squeegee
      *2
      Black Out Tape
      *3
      Release Paper
      -
      -
      *a
      Sectional View
      *b
      Non-padded Side
      *c
      Padded Side
      -
      -

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.

      HINT:
      1. Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.



    B233856E02
  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

    1. If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

      Text in Illustration 
      *1
      Squeegee
      *a
      First
      *b
      Second
      *c
      Third

  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for the corners).

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles on the tape and achieve a neat finish.

  1. Check after installation.

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

      NOTICE:
      Do not reuse the tape.



2. INSTALL REAR DOOR OUTSIDE STRIPE LH


B242549E01
  1. Refer to the illustration to position a new rear door outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    2 to 4 mm (0.078 to 0.158 in.)
    B
    4 to 6 mm (0.157 to 0.236 in.)
    C
    4 to 6 mm (0.157 to 0.236 in.)
    D
    2 to 4 mm (0.078 to 0.158 in.)
    E
    4 to 6 mm (0.157 to 0.236 in.)
    F
    2 to 4 mm (0.078 to 0.158 in.)



3. INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH


B242551E01
  1. Refer to the illustration to position a new rear door lower outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    +/- 1.0 mm (0.039 in.) From End



4. INSTALL NO. 2 BLACK OUT TAPE LH


B242550E01
  1. Refer to the illustration to position new No. 2 black out tape.

    Reference Value:
    Area
    Specified Condition
    A
    +/- 1.0 mm (0.039 in.) From End
    B
    +/- 1.0 mm (0.039 in.) From End



5. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new rear door front window frame moulding.

    1. Using a heat light, heat a new rear door front window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the rear door front window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the clip and double-sided tape to install the rear door front window frame moulding.

      HINT:
      Press the rear door front window frame moulding firmly to install it.

  1. Install a new door window frame moulding clip.



6. INSTALL REAR DOOR WEATHERSTRIP LH
  1. Attach the 3 clips to install the upper part of the rear door weatherstrip.



7. INSTALL REAR DOOR BELT MOULDING LH
  1. Attach the 7 claws to install the rear door belt moulding.



8. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the rear power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.



    B242781
  1. Operate the rear power window regulator switch assembly until the rear door window regulator sub-assembly LH reaches bottom dead center.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the rear power window regulator switch assembly.

  1. Install the front side of the rear door glass run LH.



    B242788E01
  1. Apply MP grease to the sliding areas of the rear door glass channel sub-assembly LH as shown in the illustration.
    Text in Illustration 
    *a
    5.0 mm (0.197 in.)
    *b
    157 mm (6.181 in.)
    *c
    5.0 mm (0.197 in.)
    V100155
    MP grease



    B240720
  1. Slide the rear door glass sub-assembly LH as shown in the illustration to install it.



9. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    B240718
  1. Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.



10. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    B240716E01
  1. Install the temporary bolt to the rear door window rear lower frame sub-assembly LH.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Temporarily install the rear door window rear lower frame sub-assembly LH to the rear door panel.

  1. Install the screw.

  1. Install the 2 bolts.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }

  1. Tighten the temporary bolt to install the rear door window rear lower frame sub-assembly LH.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



11. INSTALL REAR DOOR GLASS RUN LH


    B240715
  1. Install the rear door glass run LH.



12. INSTALL REAR DOOR SERVICE HOLE COVER LH
  1. Apply a new butyl tape to the rear door panel.



    B240712E01
  1. Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

  1. Install the rear door service hole cover LH according to the reference points on the rear door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the rear door service hole cover LH preventing wrinkles and air bubbles.

  1. Connect the connector.

  1. Attach the 3 clamps and rear door wire.



13. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    B240749
  1. Attach the 3 claws to install the rear door inner glass weatherstrip LH as shown in the illustration.



14. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240750
  1. Attach the claw to install the clamp.



    B242790
  1. Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.



    B242772
  1. Connect the connector.



    B357471E01
  1. Attach the rear door trim board sub-assembly LH to the 4 claws of the rear door inner glass weatherstrip LH as shown in the illustration.

  1. Attach the reference boss.
    Text in Illustration 
    *1
    Reference Boss



    B240704
  1. Attach the 9 clips to install the rear door trim board sub-assembly LH.

  1. Install the 3 screws.



    B357479
  1. Attach the 4 claws to install the 2 door armrest caps.



15. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH


    B357472
  1. Attach the 3 claws to install the rear door inside handle bezel LH.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



17. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).