Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > INSTALLATION

for Preparation Click here



1. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A229667E01
  1. Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing gear assembly in the retard direction.

  1. Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.



    A229666
  1. Tighten the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the lock of the camshaft timing gear assembly.

    1. Fix the camshaft in place and confirm that the camshaft timing gear assembly is locked.

      NOTICE:
      Be careful not to damage the camshaft.



    A229672E01
  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Open
      *4
      Close
      V100144
      Rubber
      V100145
      Vinyl Tape

      HINT:
      The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.

    2. Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.



    3. A229673E01
    4. Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      CAUTION:
      Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



    5. A229674E01
    6. Check that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Hold Pressure
      *4
      Decompress

      HINT:
      This operation releases the lock pin at the most retarded position.

    7. When the camshaft timing gear assembly reaches the most advanced position, release the air pressure first from the retard side path and next from the advance side path.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

      NOTICE:
      Do not use air pressure to perform the smooth operation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear assembly locks at the most retarded position.



    A227959E01
  1. Remove the flange bolt and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.



2. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A227956E01
  1. Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing exhaust gear in the advanced direction.

  1. Check that there is no clearance between the gear flange and camshaft.



    A229668
  1. Tighten the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the camshaft timing exhaust gear lock.

    1. Make sure that the camshaft timing exhaust gear assembly locks.



    A229675E01
  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Open
      *4
      Close
      V100144
      Rubber
      V100145
      Vinyl Tape

      HINT:
      The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.

    2. Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.



    3. A229676E01
    4. Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths (the advance side path and retard side path).
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      CAUTION:
      Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



    5. A229677E01
    6. Make sure that the camshaft timing exhaust gear assembly rotates in the retard direction when reducing the air pressure applied to the advance side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Hold Pressure
      *4
      Decompress

      HINT:
      The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.

    7. When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure first from the advance side path, and then release the air pressure from the retard side path.

      NOTICE:
      Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.

  1. Check for smooth rotation.

    1. Turn the camshaft timing exhaust gear assembly within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear assembly turns smoothly.

      NOTICE:
      When the air pressure is released from the advance side path and then from the retard side path, the gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.

  1. Check the lock at the most advanced position.

    1. Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



    A227960E01
  1. Remove the flange bolt and camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.



3. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A229667E01
  1. Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing gear assembly in the retard direction.

  1. Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.



    A229666
  1. Install the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the lock of the camshaft timing gear assembly.

    1. Fix the camshaft in place and confirm that the camshaft timing gear assembly is locked.

      NOTICE:
      Be careful not to damage the camshaft.



4. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A227956E01
  1. Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing exhaust gear assembly in the advanced direction.

  1. Check that there is no clearance between the gear flange and camshaft.



    A229668
  1. Install the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the lock of the camshaft timing exhaust gear assembly.

    1. Make sure that the camshaft timing exhaust gear assembly locks.



5. INSTALL NO. 3 CAMSHAFT


    A072945E01
  1. Check that the notch is aligned with the "0" timing mark of the timing chain cover sub-assembly.



    A227954E01
  1. Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the chain sub-assembly to the camshaft timing gear assembly.
    Text in Illustration 
    *1
    Timing Mark
    *2
    Mark Plate (yellow)
    *a
    Align

  1. Clean the camshaft housing LH and camshaft journals and apply engine oil to them.



    A221097E01
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem
    *4
    Valve Stem Cap



    A149856E01
  1. Install the chain sub-assembly to the No. 3 camshaft, and then install the No. 3 camshaft to the camshaft housing LH.
    Text in Illustration 
    *a
    Place on camshaft timing gear assembly

    HINT:
    1. Place the chain sub-assembly on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.
    2. Install the No. 3 camshaft so that the timing mark is facing upward.



6. INSTALL NO. 4 CAMSHAFT
  1. Clean the camshaft housing LH and camshaft journals and apply engine oil to them.



    A225427E01
  1. Pass the No. 4 camshaft through the chain sub-assembly from the front of the vehicle, align the mark plate (yellow) with the timing mark and install the chain sub-assembly to the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Mark Plate (yellow)
    *2
    Timing Mark



    A224770
  1. While lifting up the No. 4 camshaft, pass the No. 3 chain tensioner assembly through the chain sub-assembly and set it in place.

  1. Install the No. 4 camshaft to the camshaft housing LH, and then install the No. 3 chain tensioner assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



7. INSTALL CAMSHAFT BEARING CAP (for Bank 2)
  1. Clean the camshaft bearing caps and apply engine oil to them.



    A221097E01
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem
    *4
    Valve Stem Cap



    A226814E01
  1. Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the bolts and washers for temporary installation of the camshaft housing in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.

    Torque:
    for bolt A:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }
    for bolt B:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Installation of Bolts and Washers for Temporary Installation of camshaft housing
    *b
    Part Installation
    V100135
    Bolt A
    V100136
    Bolt B

    NOTICE:
    1. Be sure to follow the numerical order when performing this procedure.
    2. Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.

  1. Check the torque of each bolt again.



8. CONNECT CHAIN SUB-ASSEMBLY (for Bank 2)


    A225424E01
  1. Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly.
    Text in Illustration 
    *1
    Paint Mark

    HINT:
    If the paint marks are not aligned, align them by turning the camshaft slightly.



9. INSTALL CAMSHAFT


    A229679E01
  1. Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain sub-assembly can be installed easily.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.



    A227955E01
  1. Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the chain sub-assembly to the camshaft timing gear assembly.
    Text in Illustration 
    *1
    Timing Mark
    *2
    Mark Plate (yellow)
    *a
    Align

  1. Clean the camshaft housing RH and camshaft journals and apply engine oil to them.



    A221097E01
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem
    *4
    Valve Stem Cap



    A225421E01
  1. Install the chain sub-assembly to the camshaft, and then install the camshaft to the camshaft housing RH.
    Text in Illustration 
    *a
    Place on camshaft timing gear assembly

    HINT:
    1. Place the chain sub-assembly on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.
    2. Install the camshaft so that the timing mark is facing upward.



10. INSTALL NO. 2 CAMSHAFT
  1. Clean the camshaft housing RH and camshaft journals and apply engine oil to them.



    A225428E01
  1. Pass the No. 2 camshaft through the chain sub-assembly from the front of the vehicle, align the mark plate (yellow) with the timing mark and install the chain sub-assembly to the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Mark Plate (yellow)
    *2
    Timing Mark



    A224769
  1. While lifting up the No. 2 camshaft, pass the No. 2 chain tensioner assembly through the chain sub-assembly and set it in place.

  1. Install the No. 2 camshaft to the camshaft housing RH, and then install the No. 2 chain tensioner assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



11. INSTALL CAMSHAFT BEARING CAP (for Bank 1)
  1. Clean the camshaft bearing caps and apply engine oil to them.



    A221097E01
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem
    *4
    Valve Stem Cap



    A226813E01
  1. Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the bolts and washers for temporary installation of the camshaft housing in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.

    Torque:
    for bolt A:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }
    for bolt B:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Installation of Bolts and Washers for Temporary Installation of camshaft housing
    *b
    Part Installation
    V100135
    Bolt A
    V100136
    Bolt B

    NOTICE:
    1. Be sure to follow the numerical order when performing this procedure.
    2. Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.

  1. Check the torque of each bolt again.



12. CONNECT CHAIN SUB-ASSEMBLY (for Bank 1)


    A225425E01
  1. Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly.
    Text in Illustration 
    *1
    Paint Mark

    HINT:
    If the paint marks are not aligned, align them by turning the camshaft slightly.



13. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


    A226509E01
  1. Turn the crankshaft counterclockwise 30° past the "0" timing mark, and then turn it clockwise to align the notch with the "0" timing mark.

  1. Turn the crankshaft slightly to eliminate the slack in the chain sub-assembly.

    HINT:
    Make sure there is some slack in the chain sub-assembly around the area where the No. 1 chain tensioner assembly is installed.



    A178214E01
  1. While turning the stopper plate of the No. 1 chain tensioner assembly clockwise, push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.
    Text in Illustration 
    *1
    Stopper Plate
    *a
    Push

  1. While turning the stopper plate of the No. 1 chain tensioner assembly counterclockwise, insert a pin of φ1.27 mm (0.0500 in.) into the holes in the stopper plate and No. 1 chain tensioner assembly to fix the stopper plate in place.

  1. Install the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the pin from the No. 1 chain tensioner assembly.



14. INSPECT VALVE TIMING
  1. Check the camshaft timing marks.

    NOTICE:
    1. Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly.
    2. If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.



  1. Check that each camshaft timing mark is positioned as shown in the illustration.


    A224753E01


    Text in Illustration 
    *1
    Timing Mark
    -
    -
    *a
    Viewpoint
    -
    -

    HINT:
    A182780E01
    for Intake Camshaft:
    Be sure to check mark A at the point when marks B, C and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.

  1. If the valve timing is misaligned, reinstall the chain sub-assembly.

  1. Turn the crankshaft 2 revolutions, set the No. 1 cylinder to TDC/compression and check the timing marks again.



15. INSTALL TIMING CHAIN COVER PLATE
  1. Install a new gasket and the timing chain cover plate with the 4 bolts.

    Torque:
    9.1 N*m{ 93 kgf*cm , 81 in.*lbf }



16. POUR ENGINE OIL


A224782

HINT:
Before installing the cylinder head cover, pour engine oil into the locations shown in the illustration.



17. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover sub-assembly and cylinder head cover.



    A223667
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. Install 3 new gaskets.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.



    A225447E01
  1. Temporarily install the cylinder head cover sub-assembly with the 12 bolts. Tighten the bolts uniformly in several steps.

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Standard Bolt:
    Item
    Length
    A
    25 mm (0.984 in.)
    B
    35 mm (1.38 in.)
    C
    65 mm (2.56 in.)
    D
    60 mm (2.36 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Bolt C
    V100138
    Bolt D

    NOTICE:
    Do not start the engine for at least 2 hours after installation.



18. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover sub-assembly and cylinder head cover.



    A223664
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. Install 3 new gaskets.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.



    A226494E01
  1. Temporarily install the cylinder head cover sub-assembly with the 12 bolts. Tighten the bolts uniformly in several steps.

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Standard Bolt:
    Item
    Length
    A
    25 mm (0.984 in.)
    B
    35 mm (1.38 in.)
    C
    70 mm (2.76 in.)
    D
    60 mm (2.36 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Bolt C
    V100138
    Bolt D

    NOTICE:
    Do not start the engine for at least 2 hours after installation.



19. CONNECT FUEL PIPE SUB-ASSEMBLY
  1. Connect the fuel pipe sub-assembly with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



20. INSTALL REAR CYLINDER HEAD COVER
  1. Temporarily install the cover with the 3 bolts.



    A224695E01
  1. Tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



21. INSTALL NO. 2 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the No. 2 oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the No. 2 oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



22. INSTALL NO. 1 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the No. 1 oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the No. 1 oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



23. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY


    A223698E01
  1. Install the water by-pass pipe sub-assembly with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 2 hoses.
    Text in Illustration 
    *a
    Upward
    *b
    Rearward

    HINT:
    The direction of the hose clamp is indicated in the illustration.



24. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    A223631E01
  1. Install a new O-ring to the engine oil level dipstick guide.
    Text in Illustration 
    *1
    New O-Ring

  1. Apply a light coat of engine oil to the O-ring.

  1. Push the engine oil level dipstick guide end into the guide hole.

  1. Install the engine oil level dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the engine oil level dipstick.



25. INSTALL GENERATOR ASSEMBLY
  1. Install the generator bracket to the generator with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the generator bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the wire harness with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the generator connector to the generator.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.



26. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



27. INSTALL WIRING HARNESS CLAMP BRACKET
  1. Install the wiring harness clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Attach the clamp.



28. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. for Integrated Type:
    Install the No. 2 idler pulley with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. for Separate Type:
    Install the idler pulley cover plate, No. 2 idler pulley and No. 2 idler pulley cover plate with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



29. CONNECT VANE PUMP ASSEMBLY
  1. Connect the vane pump assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Attach the 2 wire harness clamps.

  1. Connect the 2 connectors.



30. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 6 ignition coil assemblies with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 6 ignition coil connectors.



31. INSTALL NO. 2 EMISSION CONTROL VALVE SET
  1. Install the No. 2 emission control valve set with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A288452E02
  1. Align the paint mark with the projection and connect the No. 1 air hose.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Projection
    *a
    Upper
    *b
    LH Side

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.

  1. Connect the No. 2 emission control valve set connector.



32. INSTALL NO. 1 EMISSION CONTROL VALVE SET
  1. Install the No. 1 emission control valve set with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A288448E01
  1. Align the paint mark with the projection and connect the No. 1 air hose.
    Text in Illustration 
    *1
    Projection
    *2
    Paint mark
    *a
    RH Side
    *b
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.

  1. Connect the No. 1 emission control valve set connector.



33. INSTALL NO. 2 AIR TUBE


    A289303E01
  1. Install 2 new gaskets to the No. 2 air tube.
    Text in Illustration 
    *1
    New Gasket
    *2
    No. 2 Air Tube

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.

  1. Install the No. 2 air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



34. INSTALL AIR TUBE


    A289302E01
  1. Install 2 new gaskets to the air tube.
    Text in Illustration 
    *1
    New Gasket
    *2
    Air Tube

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.

  1. Install the air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



35. INSTALL INTAKE AIR SURGE TANK
  1. Install a new gasket to the intake air surge tank.



    A306010E01
  1. Install the intake air surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. Install the No. 1 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the No. 2 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A225183E01
  1. Connect the No. 1 ventilation hose.
    Text in Illustration 
    *a
    Front
    *b
    Matchmark
    *c
    Top

  1. Connect the No. 1 vacuum switching valve connector.

  1. Connect the No. 1 vapor fuel feed hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.



    A225184E01
  1. Connect the throttle body connector.
    Text in Illustration 
    *a
    Front
    *b
    Matchmark
    *c
    RH

  1. Connect the No. 4 water by-pass hose.

  1. Connect the No. 5 water by-pass hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Attach the 2 heater hose clamps.



36. INSTALL AIR TUBE ASSEMBLY


  1. for Bank 1 Side:



      A226131E04
    1. Align the paint mark with the projection and connect the air tube assembly to the No. 1 emission control valve set.
      Text in Illustration 
      *a
      Projection
      *b
      Paint Mark
      *c
      Upper
      *d
      RH

      HINT:
      Make sure the direction of the hose clamp is as shown in the illustration.



  1. for Bank 2 Side:



      A226132E04
    1. Align the paint mark with the projection and connect the air tube assembly to the No. 2 emission control valve set.
      Text in Illustration 
      *a
      Paint Mark
      *b
      Projection
      *c
      Upper
      *d
      LH

      HINT:
      Make sure the direction of the hose clamp is as shown in the illustration.

  1. Install the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



37. INSTALL FAN SHROUD
  1. Install the fan pulley to the water pump.

  1. Place the fan shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.



    A229548E03
  1. Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fluid coupling to the water pump.
    Text in Illustration 
    *a
    Paint Mark

  1. Temporarily install the fan with fluid coupling to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.



    A223087
  1. Attach the claws of the shroud to the radiator as shown in the illustration.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the fan with fluid coupling and generator V-belt (Click here).

  1. Tighten the 4 nuts of the fan with fluid coupling.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



38. CONNECT OIL COOLER TUBE


    A226789
  1. Connect the oil cooler tube with the 2 bolts, and attach the claw to close the flexible hose clamp.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



39. INSTALL RADIATOR RESERVOIR TANK
  1. Install the radiator reservoir tank with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the reservoir hose to upper side of the radiator tank upper.



40. INSTALL NO. 2 RADIATOR HOSE


    A306026E03
  1. Connect the No. 2 radiator hose with the clamp so that its paint mark aligns with the radiator protrusion as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



    A227083E04
  1. Connect the No. 2 radiator hose with the clamp so that its paint mark aligns with the water inlet housing protrusion as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Front
    *d
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



41. INSTALL NO. 1 RADIATOR HOSE


    A227085E03
  1. Connect the No. 1 radiator hose to the water inlet housing with the clamp shown in the illustration labeled A.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Front
    *d
    Upper

    HINT:
    1. Make sure the paint mark of the No. 1 radiator hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.

  1. Connect the No. 1 radiator hose with the clamp so that its paint mark aligns with the radiator protrusion as shown in the illustration labeled B.

    HINT:
    1. Make sure the paint mark of the No. 1 radiator hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.



42. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner case sub-assembly with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the air cleaner filter element sub-assembly.



43. INSTALL AIR CLEANER CAP AND HOSE


    A223697E01
  1. Install the air cleaner cap and hose.
    Text in Illustration 
    *a
    Upper
    *b
    Front
    *c
    RH
    *d
    Align cutout portion of hose with protrusion of throttle
    *e
    Paint Mark

    1. Install the air cleaner cap and hose with the bolt and fasten the 4 hook clamps.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    2. Tighten the clamp.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. Attach the 4 clamps and connect the ventilation hose, vacuum hose and mass air flow meter connector.

      HINT:
      The direction of the hose clamp is indicated in the illustration.



44. INSTALL BATTERY TRAY


45. INSTALL BATTERY


46. INSTALL BATTERY HOLD DOWN CLAMP
  1. Install the battery clamp with the 2 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



47. CONNECT CABLE TO POSITIVE BATTERY TERMINAL


48. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



49. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Add engine coolant.

    Standard Capacity:
    10.5 liters (11.1 US qts, 9.2 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the F line.
    If the coolant level is below the F line, repeat steps *4 through *8.
    If the coolant level is above the F line, drain coolant until the coolant level reaches the F line.



50. ADD ENGINE OIL


  1. Add fresh engine oil.

    NOTICE:
    A308107
    Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

    If engine oil is on the location indicated by the arrow, replace the belt tensioner.

    Standard Engine Oil:

    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    0W-20


    Standard Oil Capacity:

    Item
    Specified Condition
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 Imp. qts)



51. INSPECT FOR COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



52. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



53. INSTALL V-BANK COVER


    A229926E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to attach the pins.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



54. INSTALL UPPER RADIATOR SUPPORT SEAL
  1. Install the upper radiator support seal with the 13 clips.



55. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    A224743
  1. Hook the No. 1 engine under cover sub-assembly to the vehicle body as shown in the illustration.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



56. INSTALL FRONT LOWER BUMPER COVER (w/o Intuitive Parking Assist System)
  1. Install the front lower bumper cover with the 5 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



57. INSTALL AIR INTAKE DUCT LH (w/ Intuitive Parking Assist System)
  1. Install the air intake duct LH with the 2 screws.

  1. Install the clip and bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



58. INSTALL AIR INTAKE DUCT RH (w/ Intuitive Parking Assist System)

HINT:
Use the same procedure as for the LH side.



59. INSTALL FRONT LOWER BUMPER COVER (w/ Intuitive Parking Assist System)
  1. Install the front lower bumper cover with the 4 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



60. INSTALL COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)
  1. Install the cool air intake duct with the 4 clips.



61. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IGN Advance.

    3. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    A206183E05
  1. When not using the Techstream:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

      NOTICE:
      Be sure not to improperly connect the terminals. This may damage the engine.

    2. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects primary signals.
      1. After the inspection, be sure to wrap the wire harness with tape.



    3. A076316E01
    4. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    5. Remove SST from the DLC3.

    6. Inspect the ignition timing during idling.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch off)

    7. Disconnect the timing light from the engine.