Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM

INTUITIVE PARKING ASSIST SYSTEM > OPERATION CHECK

for Preparation Click here



CHECK INITIAL CHECK FUNCTION


    E107404E10
  1. Check the initial check function for the buzzer.

    1. When the back sonar or clearance sonar switch assembly is turned on, check that the following occurs: 1) after 0.2 seconds, the buzzer sounds for approximately 0.7 to 1.3 seconds, and 2) the system starts the obstacle detection operation.

  2. Check the initial check function for the sensor.

    1. Approximately 0.2 seconds after the ignition switch is turned to ON and the back sonar or clearance sonar switch is turned on, all the sensors are checked by the system.
    2. When the shift lever is operated, the system starts the obstacle detection operation.


MALFUNCTION DISPLAY (MULTI-INFORMATION DISPLAY)


  1. Open circuit indication



    1. If there is an open circuit between the ultrasonic sensor and the clearance warning ECU assembly or a sensor is malfunctioning, the malfunction is displayed as shown in the illustration.


      E282875E01

      HINT:
      The example shows an open circuit in the ultrasonic sensor (front left sensor).



  2. Frozen indication



    1. If a sensor is covered with foreign matter, such as mud or snow, the affected sensor is displayed as shown in the illustration.


      E282876E01

      HINT:
      1. The example shows that the ultrasonic sensor (front left sensor) is covered with foreign matter.
      2. If "CLEAN SONAR" is displayed, refer to "Frozen indication is displayed in self-check function" on Problem Symptoms Table to inspect it (Click here).


DETECTION RANGE MEASUREMENT AND DISPLAY INSPECTION
  1. Detection range measurement:

    NOTICE:
    Make sure that the vehicle does not move by applying the parking brake firmly.


    1. Turn the ignition switch to ON.

    2. Move the shift lever to R to check the ultrasonic sensors.

  2. Turn the clearance sonar main switch on.



  3. Move a 60 mm (2.36 in.) diameter pole near each sensor to measure its detection range.

    NOTICE:
    These detection ranges are applicable when positioning the 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The detection range varies depending on the measuring method and type of obstacle (such as walls).

    HINT:
    Have an assistant move the pole.




    1. Clearance Sonar


      E282877E01


      Text in Illustration 
      *a
      Approx. 950 mm (37.4 in.)
      *b
      Approx. 600 mm (23.6 in.)
      *c
      Approx. 500 mm (19.7 in.)
      *d
      Approx. 200 mm (7.9 in.)
      V100144
      Hatched Area
      -
      -

      NOTICE:
      The No. 1 ultrasonic sensor side view detection range hatched area (labeled *1) represents the cross section of the top view of the lines of detection range A. The hatched area *1 does not represent the entire side view detection range.



    2. Back Sonar


      E282878E01


      Text in Illustration 
      *a
      Approx. 1800 mm (70.9 in.)
      *b
      Approx. 1350 mm (53.1 in.)
      *c
      Approx. 1500 mm (59.1 in.)
      *d
      Approx. 200 mm (7.9 in.)
      *e
      Wall
      *f
      Approx. 600 mm (23.6 in.)
      V100144
      Hatched Area
      -
      -



  4. When the ultrasonic sensors (front corner sonar) have detected an obstacle, check the displays and check that the buzzer sounds.

    Operation Condition 
    Ignition Switch
    Clearance Sonar Main Switch
    Shift Lever Position
    Vehicle Speed
    ON
    On
    In any position other than P
    1. Less than approximately 15 km/h (9.3 mph) if speed is increasing
    2. Less than approximately 10 km/h (6.2 mph) if speed is decreasing


    E282879E01


    Standard:

    Multi-information Display and Buzzer 
    Detection Range
    During Judgment
    Obstacle
    *1
    Close-range detection
    Within approx. 300 +/- 30 mm (11.8 +/- 1.2 in.)
    Buzzer: Sounds continuously
    60 mm (2.36 in.) diameter pole
    *2
    Medium-range detection
    From approx. 300 +/- 30 to 450 +/- 50 mm (11.8 +/- 1.2 to 15.7 +/- 1.6 in.)
    Buzzer: Sounds intermittently (ON: 0.075 sec. / OFF: 0.075 sec.)
    60 mm (2.36 in.) diameter pole
    *3
    Long-range detection
    From approx. 450+/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.)
    Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.15 sec.)
    60 mm (2.36 in.) diameter pole

    HINT:
    Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.



  5. When the ultrasonic sensors (rear corner sonar) have detected an obstacle, check the displays and check that the buzzer sounds.

    Operation Condition 
    Ignition Switch
    Clearance Sonar Main Switch
    Shift Lever Position
    Vehicle Speed
    ON
    On
    R
    -


    E282880E01


    Standard:

    Multi-information Display and Buzzer 
    Detection Range
    During Judgment
    Obstacle
    *1
    Close-range detection
    Within approx. 300 +/- 30 mm (11.8 +/- 1.2 in.)
    Buzzer: Sounds continuously
    60 mm (2.36 in.) diameter pole
    *2
    Medium-range detection
    From approx. 300 +/- 30 to 450 +/- 50 mm (11.8 +/- 1.2 to 17.7 +/- 2.0 in.)
    Buzzer: Sounds intermittently (ON: 0.075 sec. / OFF: 0.075 sec.)
    60 mm (2.36 in.) diameter pole
    *3
    Long-range detection
    From approx. 450+/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.)
    Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.15 sec.)
    60 mm (2.36 in.) diameter pole

    HINT:
    Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.



  6. When the ultrasonic sensors (back sonar) have detected an obstacle, check the displays and check that the buzzer sounds.

    Operation Condition 
    Ignition Switch
    Clearance Sonar Main Switch
    Shift Lever Position
    Vehicle Speed
    ON
    On
    R
    -


    E282881E01


    Standard:

    Multi-information Display and Buzzer 
    Detection Range
    During Detection
    Obstacle
    *1
    Close-range detection
    Within approx. 350 +/- 40 mm (13.8 +/- 1.6 in.)
    Buzzer: Sounds continuously
    60 mm (2.36 in.) diameter pole
    *2
    Medium-range detection
    From approx. 350 +/- 40 to 450 +/- 50 mm (13.8 +/- 1.6 to 17.7 +/- 2.0 in.)
    Buzzer: Sounds intermittently (ON: 0.075 sec. / OFF: 0.075 sec.)
    60 mm (2.36 in.) diameter pole
    *3
    Long-range detection
    From approx. 450 +/- 50 to 600 +/- 60 mm (17.7 +/- 2.0 to 23.6 +/- 2.4 in.)
    Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.15 sec.)
    60 mm (2.36 in.) diameter pole
    *4
    Longest-range detection
    From approx. 600 +/- 60 to 1500 +/- 150 mm (23.6 +/- 2.4 to 59.1 +/- 5.9 in.)
    Buzzer: Sounds intermittently (ON: 0.15 sec. / OFF: 0.65 sec.)
    Wall

    HINT:
    Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.