Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2658    Short in Sensor with Motor Power Supply Circuit

for Preparation Click here


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC Code
DTC Detection Condition
Trouble Area
B2658
A problem with the voltage supplied to the position control sensor.
  1. Front power seat switch LH
  2. Separate type front seat cushion spring assembly LH
  3. Separate type front seatback spring assembly LH
  4. Harness or connector

WIRING DIAGRAM


B357485E01


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - SLIDE MOTOR)
  1. Disconnect the b19 front power seat switch LH connector.

  1. Disconnect the b15 slide motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b19-5 (SSRS) - b15-2 (O/P)
    Always
    Below 1 Ω
    b19-1 (SGND) - b15-3 (GND)
    Always
    Below 1 Ω
    b19-5 (SSRS) - b19-1 (SGND)
    Always
    10 kΩ or higher
    b19-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    b19-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK FRONT POWER SEAT SWITCH LH (SLIDE MOTOR CIRCUIT)


    B238255E25
  1. Connect the b19 front power seat switch LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b15-2 (O/P) - b15-3 (GND)
    Sliding switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



NG
REPLACE FRONT POWER SEAT SWITCH LH
OK


4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)
  1. Disconnect the b19 front power seat switch LH connector.

  1. Disconnect the b16 front vertical motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b19-3 (SSFV) - b16-2 (O/P)
    Always
    Below 1 Ω
    b19-1 (SGND) - b16-3 (GND)
    Always
    Below 1 Ω
    b19-3 (SSFV) - b19-1 (SGND)
    Always
    10 kΩ or higher
    b19-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    b19-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK FRONT POWER SEAT SWITCH LH (FRONT VERTICAL MOTOR CIRCUIT)


    B238255E26
  1. Connect the b19 front power seat switch LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b16-2 (O/P) - b16-3 (GND)
    Front vertical switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



NG
REPLACE FRONT POWER SEAT SWITCH LH
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - LIFTER MOTOR)
  1. Disconnect the b19 front power seat switch LH connector.

  1. Disconnect the b17 lifter motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b19-4 (SSRL) - b17-2 (O/P)
    Always
    Below 1 Ω
    b19-1 (SGND) - b17-3 (GND)
    Always
    Below 1 Ω
    b19-4 (SSRL) - b19-1 (SGND)
    Always
    10 kΩ or higher
    b19-4 (SSRL) - Body ground
    Always
    10 kΩ or higher
    b19-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK FRONT POWER SEAT SWITCH LH (LIFTER MOTOR CIRCUIT)


    B238255E27
  1. Connect the b19 front power seat switch LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b17-2 (O/P) - b17-3 (GND)
    Lifter switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly LH [Lifter Motor])



NG
REPLACE FRONT POWER SEAT SWITCH LH
OK


8.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - RECLINING MOTOR)
  1. Disconnect the b19 front power seat switch LH connector.

  1. Disconnect the d5 reclining motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b19-11 (SSRR) - d5-2 (O/P)
    Always
    Below 1 Ω
    b19-1 (SGND) - d5-3 (GND)
    Always
    Below 1 Ω
    b19-11 (SSRR) - b19-1 (SGND)
    Always
    10 kΩ or higher
    b19-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    b19-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK FRONT POWER SEAT SWITCH LH (RECLINING MOTOR CIRCUIT)


    B238255E28
  1. Connect the b19 front power seat switch LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    d5-2 (O/P) - d5-3 (GND)
    Reclining switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



NG
REPLACE FRONT POWER SEAT SWITCH LH
OK


10.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH
  1. Temporarily replace the separate type front seat cushion spring with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 11
OK

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH IS DEFECTIVE) 

11.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH
  1. Temporarily replace the separate type front seatback spring with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
REPLACE FRONT POWER SEAT SWITCH LH
OK

END (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH IS DEFECTIVE)