Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > ABS Warning Light Remains ON

for Preparation Click here


DESCRIPTION

If any of the following is detected, the ABS warning light remains on.
  1. The skid control ECU connectors are disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and skid control ECU.
  4. The anti-lock brake system is defective.
  5. The voltage at terminal IG1 is high.
  6. The rear differential is locked.*
*: w/ Rear Differential Lock

HINT:
It may not be possible to use the Techstream when the skid control ECU is abnormal.


WIRING DIAGRAM


C293371E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check the skid control ECU connector connection.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


4.READ VALUE USING TECHSTREAM (IG1 VOLTAGE VALUE)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG1 Voltage Value
    IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
    Ignition switch ON: 11 to 14 V
    -

  1. Check the voltage output from the skid control ECU displayed on the Techstream.

    OK:
    The output voltage displayed on the Techstream is within 11 to 14 V.



NG
Go to step 7
OK


5.CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A6 skid control ECU connector.



    C214161E11
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-40 (EXI3) - Body ground
    Ignition switch ON
    w/ Rear Differential Lock: Rear differential free
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 4WD)
    B
    NG (for 2WD)
    C



B
Go to step 9

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


6.READ VALUE USING TECHSTREAM (ABS WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light/ ON or OFF
OFF
-
  1. When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (Click here).


ABS/VSC/TRAC 
Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON/OFF
Observe the combination meter.

Result 
Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

7.CHECK TERMINAL VOLTAGE (IG1)
  1. Disconnect the A6 skid control ECU connector.



    C214161E22
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
  1. Disconnect the A6 and A7 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A6-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A7-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
  1. Disconnect the A6 skid control ECU connector.

  1. Disconnect the F47 four wheel drive control ECU connector.

  1. w/ Rear Differential Lock:
    Disconnect the D3 rear differential lock detection switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-40 (EXI3) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/o Rear Differential Lock)
    A
    OK (w/ Rear Differential Lock)
    B
    NG
    C



B
Go to step 11

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


10.CHECK TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A6 skid control ECU connector.

  1. Connect the F47 four wheel drive control ECU connector.



    C214161E11
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

11.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH)
  1. Remove the rear differential lock detection switch (Click here).



    C214518E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (+B) - 1 (GND)
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Differential Lock Detection Switch (Differential Lock Position Switch))



NG
REPLACE REAR DIFFERENTIAL LOCK DETECTION SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH) (Click here)
OK


12.INSPECT TERMINAL VOLTAGE (EXI3)
  1. Disconnect the A6 skid control ECU connector.

  1. Connect the F47 four wheel drive control ECU connector.



    C214161E11
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)