Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > AUTO LSD Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

The AUTO LSD does not operate even if the VSC OFF switch is pressed under the following conditions:
  1. The brake system is faulty.
  2. The temperature inside the hydraulic brake booster increases and the AUTO LSD operation is suspended.

WIRING DIAGRAM

Refer to AUTO LSD Indicator Light Remains ON .

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).



    C215409E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (OFF) - 3 (VSC)
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch)



NG
REPLACE VSC OFF SWITCH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Disconnect the A6 skid control ECU connector.

  1. Disconnect the U6 VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-9 (CSW) - U6-6 (OFF)
    Always
    Below 1 Ω
    A6-9 (CSW) - Body ground
    Always
    10 kΩ or higher
    U6-3 (VSC) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.READ VALUE USING TECHSTREAM (AUTO LSD INDICATOR LIGHT)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Auto LSD Indicator Light
Auto LSD indicator light/ ON or OFF
ON: Indicator light on
OFF: Indicator light off
-
  1. When performing the Auto LSD Indicator Light Active Test, check Auto LSD Indicator Light in the Data List (Click here).


ABS/VSC/TRAC 
Tester Display
Test Part
Control Range
Diagnostic Note
Auto LSD Indicator Light
Auto LSD indicator light
Indicator light ON/OFF
Observe the combination meter.

Result 
Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)