Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Crawl Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

If any of the following conditions are met, the crawl indicator light blinks and crawl control is stopped.
  1. Crawl control is operated when the vehicle stability control system is malfunctioning, or a vehicle stability control system malfunction occurs during crawl control.
  2. The transfer is shifted to H4 during crawl control.
  3. The shift lever is moved to P or N during crawl control.
  4. The driver door is opened during crawl control.
When the vehicle is driven at 25 km/h (16 mph) or more during crawl control, control is temporarily stopped and the crawl indicator light blinks.
When using crawl control continually for a long period of time, if the temperature inside the hydraulic brake booster becomes too high, the crawl indicator light will turn off after blinking. After a while, the temperature decreases and crawl control becomes operable.

WIRING DIAGRAM


C214521E03


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.READ VALUE USING TECHSTREAM (CRAWL CONTROL MAIN SWITCH)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / D-SEAT SW / Data List.

    D-SEAT SW 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Main Switch
    Crawl control switch/ ON or OFF
    ON: Crawl switch on
    OFF: Crawl switch off
    -

    OK:
    The Techstream displays ON or OFF according to crawl control switch operation.



NG
Go to step 5
OK


4.READ VALUE USING TECHSTREAM (CRAWL CONTROL LIGHT)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


ABS/VSC/TRAC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Crawl Control Light
Crawl control indicator light/ ON or OFF
ON: Indicator light on
OFF: Indicator light off
-
  1. When performing the Crawl Control Light Active Test, check Crawl Control Light in the Data List (Click here).


ABS/VSC/TRAC 
Tester Display
Test Part
Control Range
Diagnostic Note
Crawl Control Light
Crawl control indicator light
Indicator light ON/OFF
Observe the combination meter.

Result 
Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

5.CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, +B, GND)
  1. Disconnect the U1 drive monitor switch connector.



    C217212E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    U1-6 (+B) - Body ground
    Always
    11 to 14 V
    U1-12 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U1-7 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Drive Monitor Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVE MONITOR SWITCH (Click here)