Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)


    B353485
  1. Remove the 4 clips and cool air intake duct.



4. REMOVE FRONT LOWER BUMPER COVER (w/o Intuitive Parking Assist System)
  1. Remove the clip, 5 bolts and front lower bumper cover.



5. REMOVE FRONT LOWER BUMPER COVER (w/ Intuitive Parking Assist System)
  1. Remove the clip, 4 bolts and front lower bumper cover.



6. REMOVE AIR INTAKE DUCT LH (w/ Intuitive Parking Assist System)


    B353484
  1. Remove the clip and bolt.

  1. Remove the 2 screws and air intake duct LH.



7. REMOVE AIR INTAKE DUCT RH (w/ Intuitive Parking Assist System)

HINT:
Use the same procedure as for the LH side.



8. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.



    A224743
  1. Unhook the No. 1 engine under cover sub-assembly from the vehicle body as shown in the illustration.



9. DRAIN ENGINE COOLANT


CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



A273797E01


Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug (RH side)
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.



10. REMOVE V-BANK COVER


    A229925E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then detach the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



11. REMOVE NO. 1 AIR CLEANER HOSE


    A221455
  1. Disconnect the ventilation hose and vacuum hose.

  1. Detach the wire harness clamp.

  1. Remove the bolt and loosen the 2 hose clamps.

  1. Remove the No. 1 air cleaner hose.



12. REMOVE AIR TUBE ASSEMBLY


  1. for Bank 1 Side:



      A221459
    1. Remove the bolt and disconnect the air tube assembly from the No. 1 emission control valve set.



  1. for Bank 2 Side:



      A221458
    1. Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.



13. REMOVE INTAKE AIR SURGE TANK


    A221456
  1. Disconnect the throttle body connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.



    A221457
  1. Disconnect the No. 1 fuel vapor feed hose.

  1. Disconnect the No. 1 vacuum switching valve connector.

  1. Disconnect the No. 1 ventilation hose.



    A221464
  1. Detach the 2 heater hose clamps.



    A221460
  1. Remove the 2 bolts and throttle body bracket.



    A225628
  1. Using a clip remover, detach the wire harness clamp.



    A221462
  1. Remove the 2 bolts and No. 1 surge tank stay.



    A221463
  1. Remove the 2 bolts and No. 2 surge tank stay.



    A221465
  1. Remove the 2 nuts, 4 bolts and intake air surge tank.

  1. Remove the gasket.



14. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A223035
  1. Disconnect the No. 1 fuel pipe sub-assembly (Click here).



15. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY


    A223036
  1. Disconnect the No. 2 fuel pipe sub-assembly (Click here).



16. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A223037
  1. Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.



17. REMOVE INTAKE MANIFOLD


    A221466
  1. Remove the 4 nuts, 6 bolts, intake manifold and 2 gaskets.