Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > REMOVAL

for Preparation Click here



1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.



2. REMOVE V-BANK COVER


    A229925E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then detach the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



3. REMOVE AIR CLEANER CAP AND HOSE


    A224721
  1. Remove the air cleaner cap and hose.

    1. Disconnect the mass air flow meter connector, vacuum hose and ventilation hose and detach the 4 clamps.

    2. Loosen the clamp.

    3. Unfasten the 4 hook clamps, and then remove the bolt and air cleaner cap and hose.



4. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.



    A224715
  1. Detach the wire harness clamp.

  1. Remove the 3 bolts and air cleaner case sub-assembly.



5. REMOVE FRONT FENDER APRON SEAL LH


    A223334
  1. w/ KDSS:
    Remove the 7 clips and front fender apron seal LH.



    A223333
  1. w/o KDSS:
    Remove the 5 clips and front fender apron seal LH.



6. REMOVE FRONT FENDER APRON SEAL RH


    A223336
  1. Remove the 4 clips and front fender apron seal RH.



7. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH


    A223335
  1. Remove the 5 clips and front No. 1 fender apron to frame seal LH.



8. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH


    A223337
  1. Remove the 5 clips and front No. 1 fender apron to frame seal RH.



9. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


10. REMOVE NO. 2 MANIFOLD STAY


    A221486
  1. Remove the 3 bolts and No. 2 manifold stay.



11. REMOVE AIR TUBE


    A288445
  1. Remove the 2 bolts, 2 nuts and air tube.

  1. Remove the 2 gaskets from the air tube.

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.



12. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A222188
  1. Remove the 3 bolts and No. 1 exhaust manifold heat insulator.



13. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A222089
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 6 nuts, exhaust manifold sub-assembly RH and gasket.



14. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    A223682E01
  1. Using SST, remove the air fuel ratio sensor from the exhaust manifold sub-assembly RH.

    SST
    09224-00010  

    NOTICE:
    Do not use the air fuel ratio sensor if it has been subjected to physical shocks, such as being dropped, etc.



15. REMOVE MANIFOLD STAY


    A222091
  1. Remove the 3 bolts and manifold stay.



16. REMOVE NO. 2 AIR TUBE


    A288449
  1. Remove the 2 bolts, 2 nuts and No. 2 air tube.

  1. Remove the 2 gaskets from the No. 2 air tube.

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.



17. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A289304
  1. Remove the 3 bolts and No. 2 exhaust manifold heat insulator.



18. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A222092
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 6 nuts, exhaust manifold sub-assembly LH and gasket.



19. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)


    A223684E01
  1. Using SST, remove the air fuel ratio sensor from the exhaust manifold sub-assembly LH.

    SST
    09224-00010  

    NOTICE:
    Do not use the air fuel ratio sensor if it has been subjected to physical shocks, such as being dropped, etc.