Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL FUEL TANK TO FILLER PIPE HOSE


    A230982E01
  1. Install the fuel tank to filler pipe hose to the fuel tank.
    Text in Illustration 
    *1
    Fuel Tank Side Mark
    *2
    Hose Side Mark

    HINT:
    Align the fuel tank side mark with the hose side mark when installing the hose.



2. INSTALL NO. 3 FUEL TANK PROTECTOR


    A220823
  1. Install the No. 3 fuel tank protector and attach the 4 clamps.

  1. Install the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



3. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Apply a light coat of gasoline or grease to a new gasket and install the gasket to the fuel tank.



    A220825E01
  1. Install the fuel suction with pump and gauge tube into the fuel tank.
    Text in Illustration 
    *1
    Protrusion
    *2
    Groove

    HINT:
    Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Put the new retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.



    A220827E01
  1. Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank, as shown in the illustration.

    SST
    09808-14020  
    Text in Illustration 
    *1
    Fuel Tank Side Mark
    *2
    Retainer Side Mark

    HINT:
    Fit the tips of SST onto the ribs of the retainer.



4. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY


    A220829
  1. Install the fuel tank main tube and fuel return tube with the 2 fuel tube joint clips.

    NOTICE:

    1. A118171E07
      Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the fuel tube joint clips are on the collars of the fuel tube joints.
    4. After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.
      Text in Illustration 
      *1
      Fuel Tube Joint
      *2
      O-Ring
      *3
      Fuel Tube
      *4
      Fuel Tube Joint Clip
      *a
      CORRECT
      *b
      INCORRECT



    A225442
  1. Install the fuel tank main tube and fuel return tube to the fuel tank.



5. INSTALL FUEL TANK BREATHER TUBE SUB-ASSEMBLY


    A227935
  1. Install the fuel tank breather tube (Click here).



6. INSTALL NO. 1 FUEL TANK PROTECTOR


    A232961
  1. Install the fuel tank protector to the fuel tank.



7. INSTALL FUEL TANK CUSHION


    A220812E01
  1. Install 3 new fuel tank cushions to the fuel tank.
    Text in Illustration 
    *1
    No. 1 Fuel Tank Cushion
    *2
    No. 2 Fuel Tank Cushion
    *3
    No. 3 Fuel Tank Cushion



8. INSTALL FUEL TANK SUB-ASSEMBLY
  1. Set the fuel tank on a transmission jack and lift up the transmission jack.

    NOTICE:
    Do not allow the fuel tank to contact the vehicle, especially the differential.



    A220832
  1. Install the 2 fuel tank bands with the 2 pins and 2 clips.

  1. Connect the 2 fuel tank bands with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



9. CONNECT FUEL TANK TO FILLER PIPE HOSE
  1. Connect the fuel tank to filler pipe hose to the filler pipe.



10. CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY
  1. Connect the fuel tank breather tube (Click here).



11. CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


    A225443
  1. Connect the fuel tank breather tube (Click here).



12. CONNECT FUEL RETURN TUBE SUB-ASSEMBLY


    A223269
  1. Connect the fuel return tube (Click here).



13. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A220806
  1. Connect the fuel tank main tube (Click here).



14. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
  1. for Half Cover Type:
    Install the No. 1 fuel tank protector with the 4 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. for Standard Type:
    Install the No. 1 fuel tank protector with the 6 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



15. INSTALL REAR FLOOR SERVICE HOLE COVER
  1. Connect the fuel pump and fuel sender gauge connector.

  1. Install the rear floor service hole cover with the 3 screws.



16. INSTALL REAR SEAT ASSEMBLY LH
  1. for 60/40 Split Double-folding Seat Type LH Side:
    Install the rear seat assembly LH (Click here).

  1. for 60/40 Split Slide Walk-in Seat Type LH Side:
    Install the rear seat assembly LH (Click here).



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



18. INSPECT FOR FUEL LEAK
  1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON and turn the Techstream on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check that there are no leaks from the fuel system.
      If there are fuel leaks, repair or replace parts as necessary.

    5. Turn the ignition switch off.

    6. Disconnect the Techstream from the DLC3.