Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2327    Lost Communication with Back Door Power Window ECU (Abnormal Power Supply)

DTC    B2328    Back Door Power Window ECU Communication Malfunction

for Preparation Click here


DESCRIPTION

  1. DTC B2327 is stored when LIN communication between the multiplex network door ECU (back door P/W) and back door power window regulator motor assembly stops for 10 seconds or more.
  2. DTC B2328 is stored when a malfunction in the LIN communication bus between the multiplex network door ECU (back door P/W) and back door power window regulator motor assembly is detected consecutively 3 times.

    DTC Code
    DTC Detection Condition
    Trouble Area
    B2327
    No communication between the multiplex network door ECU (back door P/W) and back door power window regulator motor assembly for 10 seconds or more.
    1. Multiplex network door ECU (back door P/W)
    2. Back door power window regulator motor assembly
    3. Harness or connector
    B2328
    The multiplex network door ECU (back door P/W) detects a malfunction in the LIN communication bus between the multiplex network door ECU (back door P/W) and back door power window regulator motor assembly consecutively 3 times.
    1. Multiplex network door ECU (back door P/W)
    2. Back door power window regulator motor assembly
    3. Harness or connector

WIRING DIAGRAM


C211493E24


INSPECTION PROCEDURE

NOTICE:
When using the Techstream with the ignition switch off to troubleshoot:
Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2327 or B2328 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR)
  1. Disconnect the W10 multiplex network door ECU (back door P/W) connector.

  1. Disconnect the W9 back door power window regulator motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W10-11 (MPX2) - W9-9 (LIN)
    Always
    Below 1 Ω
    W10-6 (BDR2) - W9-2 (B)
    Always
    Below 1 Ω
    W10-1 (E4) - W9-1 (GND)
    Always
    Below 1 Ω
    W10-1 (E4) - Body ground
    Always
    Below 1 Ω
    W9-1 (GND) - Body ground
    Always
    Below 1 Ω
    W10-11 (MPX2) or W9-9 (LIN) - Body ground
    Always
    10 kΩ or higher
    W10-6 (BDR2) or W9-2 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Temporarily replace the back door power window regulator motor assembly with a new or normally functioning one (Click here).


NEXT


5.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2327 or B2328 is not output.



NG
REPLACE MULTIPLEX NETWORK DOOR ECU (Click here)
OK

END (BACK DOOR POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)