REAR CENTER SEAT OUTER BELT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side) > REMOVAL |
| 1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH |
Remove the rear No. 1 seat assembly LH (Click here).
| 2. REMOVE REAR SEAT UPPER RECLINING COVER LH |
![]() |
Using a screwdriver, detach the 3 claws and remove the cover.
| *1 | Protective Tape |
| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Remove the 3 screws and handle.
| 4. REMOVE CENTER SEAT HINGE COVER RH |
![]() |
Using a clip remover, remove the clip.
Detach the 2 guides and remove the cover.
| 5. REMOVE REAR SEAT CUSHION MOULDING LH |
![]() |
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the moulding in the direction of the arrow to detach the guide and remove the moulding.
| 6. REMOVE REAR SEATBACK LOCK STRIKER COVER LH |
![]() |
Using a clip remover, detach the 3 clips and remove the cover.
| 7. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
Detach the hooks.
![]() |
Detach the hook and remove the seat cushion cover with pad.
| 8. REMOVE CENTER SEATBACK ASSEMBLY |
![]() |
Remove the 2 bolts and center seatback.
| 9. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
![]() |
Remove the bolt and inner belt, and disconnect the center outer belt.
| 10. REMOVE RECLINING ADJUSTER KNOB CAP LH |
![]() |
Using a screwdriver, detach the claw and guide, and then remove the cap.
| *1 | Protective Tape |
| 11. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
![]() |
Remove the 2 screws.
![]() |
Disconnect the cable in the order shown in the illustration and remove the lever.
| 12. REMOVE SEAT BELT ANCHOR COVER CAP |
![]() |
Using a screwdriver, detach the 2 claws and remove the cap.
| *1 | Protective Tape |
| 13. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Detach the 2 claws and 2 guides, and then remove the cover.
Disconnect the outer belt from the cover.
| 14. REMOVE REAR SEATBACK COVER |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 15. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH |
![]() |
Using a clip remover, detach the 7 clips and remove the carpet.
| 16. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Detach the 4 claws and remove the 2 supports.
| 17. REMOVE SEATBACK COVER WITH PAD |
![]() |
Remove the hog rings and detach the hooks, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
![]() |
Disconnect the outer belt from the seatback cover with pad.
| 18. REMOVE REAR SEATBACK EDGE PROTECTOR |
Remove the protector from the seatback frame.
| 19. REMOVE REAR SEAT SHOULDER BELT GUIDE |
![]() |
Detach the claw and guide, and then remove the belt guide.
| 20. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH |
![]() |
Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.