REAR CENTER SEAT OUTER BELT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side) > REMOVAL |
| 1. REMOVE REAR SEAT ASSEMBLY RH |
Remove the rear No. 1 seat assembly RH (Click here).
| 2. REMOVE NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Plastic Seatback Board) |
![]() |
Using a clip remover, detach the 2 clips.
Detach the guide and remove the board.
| 3. REMOVE NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Seatback Board with Carpet) |
![]() |
Using a clip remover, detach the 3 clips.
Detach the guide and remove the board.
| 4. REMOVE REAR SEAT INNER RECLINING COVER RH |
![]() |
Remove the screw.
Detach the 2 guides and remove the cover.
| 5. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY |
![]() |
Detach the fastening tape and remove the band.
Remove the bolt and inner belt.
| *1 | Band |
| 6. REMOVE CENTER SEATBACK COVER SUB-ASSEMBLY |
![]() |
Remove the screw.
Detach the 2 guides and remove the cover.
| 7. REMOVE CENTER SEATBACK ASSEMBLY |
![]() |
Using a T45 "TORX" socket wrench, remove the "TORX" bolt and bush.
Remove the 2 bolts and center seatback.
| 8. REMOVE CENTER NO. 2 SEATBACK COVER |
![]() |
Remove the screw.
Detach the 2 claws and remove the cover.
| 9. REMOVE REAR SEATBACK LOCK COVER RH |
![]() |
Using a moulding remover, detach the claw.
Move the cover in the direction of the arrow to detach the clip and 2 guides and remove the cover.
| 10. REMOVE REAR SEATBACK LOCK ASSEMBLY RH |
![]() |
Remove the 2 hog rings.
![]() |
Remove the 2 bolts.
While moving the release button in the direction of the arrow in the illustration, detach it from the grommet and remove the seatback lock.
| 11. REMOVE REAR SEATBACK STOP BUTTON GROMMET |
![]() |
Detach the 3 claws and remove the grommet.
| 12. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Detach the 4 claws and remove the 2 supports.
| 13. REMOVE SEAT BELT ANCHOR COVER CAP |
![]() |
Using a screwdriver, detach the 2 claws and 2 guides, and then remove the cap.
| *1 | Protective Tape |
| 14. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Remove the screw.
Detach the 3 claws and remove the cover.
Disconnect the outer belt from the cover.
| 15. REMOVE REAR SEATBACK LOCK STRIKER PROTECTOR |
![]() |
Remove the protector from the striker.
| 16. REMOVE REAR SEAT LOCK STRIKER |
![]() |
Using a T45 "TORX" socket wrench, remove the striker.
| 17. REMOVE SEATBACK COVER WITH PAD |
![]() |
Remove the hog rings, detach the hook, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
Disconnect the outer belt from the seatback cover with pad.
| 18. REMOVE REAR SEATBACK EDGE PROTECTOR |
Remove the protector from the seatback frame.
| 19. REMOVE REAR SEAT SHOULDER BELT GUIDE |
![]() |
Detach the claw and guide, and then remove the belt guide.
| 20. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH |
![]() |
Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.