Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P144C    Open in Secondary Air Injection System Heater Control Circuit

DTC    P144D    Short in Secondary Air Injection System Heater Control Circuit

for Preparation Click here


DESCRIPTION

The ECM operates the air pump heater relay which causes the air pump heater to operate.

DTC No.
DTC Detection Condition
Trouble Area
P144C
Open or short in the air pump heater relay (AIR PUMP HTR) circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay (AIR PUMP HTR) circuit
  2. Air pump heater relay (AIR PUMP HTR)
  3. ECM
P144D
Open or short in the air pump heater relay (AIR PUMP HTR) circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay (AIR PUMP HTR) circuit
  2. Air pump heater relay (AIR PUMP HTR)
  3. ECM

MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air pump heater relay (AIR PUMP HTR) circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the air pump heater relay (AIR PUMP HTR) is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the air pump heater relay (AIR PUMP HTR) is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.
  1. The battery voltage is not applied to terminal HAI1 while the air pump heater relay (AIR PUMP HTR) is off.
  2. The battery voltage is applied to terminal HAI1 while the air pump heater relay (AIR PUMP HTR) is on.

MONITOR STRATEGY


Related DTCs
P144C: Secondary air injection system air pump heater circuit range check low voltage
P144D: Secondary air injection system air pump heater circuit range check high voltage
Required Sensors/Components
Air pump heater relay (AIR PUMP HTR)
Required Sensors/Components
ECM
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P144C 
Monitor runs whenever following DTCs not stored
None
Current air pump heater relay (AIR PUMP HTR) state
OFF
Last air pump heater relay (AIR PUMP HTR) state
OFF
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

P144D 
Monitor runs whenever following DTCs not stored
None
Current air pump heater relay (AIR PUMP HTR) state
ON
Last air pump heater relay (AIR PUMP HTR) state
ON
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


P144C 
Air pump heater relay (AIR PUMP HTR) output terminal voltage
Low

P144D 
Air pump heater relay (AIR PUMP HTR) output terminal voltage
High

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait for 10 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Air Pump Heater.
  8. Activate the air pump heater for 10 seconds or more.

    HINT:
    1. The active test activates the air pump heater for up to 60 seconds.
    2. To protect the air pump heater, do not perform this test more than 4 times in a row.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
  10. Read Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P144C or P144D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  14. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.


WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AIR PUMP HEATER RELAY (AIR PUMP HTR)
  1. Inspect the air pump heater relay (AIR PUMP HTR) (Click here).



NG
REPLACE AIR PUMP HEATER RELAY (AIR PUMP HTR)
OK


2.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
  1. Remove the air pump heater relay (AIR PUMP HTR).



    A288678E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Air Pump Heater Relay (AIR PUMP HTR)
    *2
    Engine Room Relay Block

  1. Reinstall the air pump heater relay (AIR PUMP HTR).



NG
Go to step 4
OK


3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY)
  1. Remove the Air pump heater relay (AIR PUMP HTR).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay (AIR PUMP HTR) terminal 1 - C38-20 (HAI1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay (AIR PUMP HTR) terminal 1 or C38-20 (HAI1) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the Air pump heater relay (AIR PUMP HTR).

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - AIR PUMP HEATER RELAY)
  1. Remove the Air pump heater relay (AIR PUMP HTR).

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay (AIR PUMP HTR) terminal 2 - A45-5 (+B)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay (AIR PUMP HTR) terminal 2 or A45-5 (+B) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the Air pump heater relay (AIR PUMP HTR).

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)
A288982E01
  1. Disconnect the air injection control driver connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A44-1 (BATT) - Body ground
    Always
    11 to 14 V (near battery voltage)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Reconnect the air injection control driver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND))
  1. Disconnect the ECM connector.

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B37-23 (AIRP) - A45-4 (SIP)
    Always
    Below 1 Ω
    B36-26 (AIRV) - A45-3 (SIV)
    Always
    Below 1 Ω
    B37-30 (AIDI) - A45-2 (DI)
    Always
    Below 1 Ω
    A45-1 (E) - Body ground
    Always
    Below 1 Ω
    B37-23 (AIRP) or A45-4 (SIP) - Body ground
    Always
    10 kΩ or higher
    B36-26 (AIRV) or A45-3 (SIV) - Body ground
    Always
    10 kΩ or higher
    B37-30 (AIDI) or A45-2 (DI) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air injection control driver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
A200902E60
  1. Disconnect the air injection control driver connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A45-2 (DI) - A45-1 (E)
    Ignition switch ON
    11 to 14 V (near battery voltage)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Reconnect the air injection control driver connector.



NG
REPLACE ECM (Click here)
OK

REPLACE AIR INJECTION CONTROL DRIVER (Click here)