Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B1287    Back Door ECU Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is stored when LIN communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code
DTC Detection Condition
Trouble Area
B1287
No communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Multiplex network door ECU (back door P/W)
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

WIRING DIAGRAM


C218161E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the ignition switch off to troubleshoot:
    Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1287 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK DOOR ECU)
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).

  1. Disconnect the V2 multiplex network door ECU (back door P/W) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - V2-16 (MPX1)
    Always
    Below 1 Ω
    A-16 (LIN2) or V2-16 (MPX1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)


    C218162E01
  1. Disconnect the V2 multiplex network door ECU (back door P/W) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V2-6 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Multiplex Network Door ECU [Back Door P/W])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE MULTIPLEX NETWORK DOOR ECU
  1. Temporarily replace the multiplex network door ECU (back door P/W) with a new or normally functioning one (Click here).


NEXT


6.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1287 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (MULTIPLEX NETWORK DOOR ECU IS DEFECTIVE)