Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY

FRONT SEAT SIDE AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the power seat RH and power seat LH sides.
  2. The procedure listed below is for the power seat LH side.



1. PRECAUTION

CAUTION:
  1. Be sure to read Precaution thoroughly before servicing (Click here).
  2. If the side airbag was deployed, replace the separate type front seatback assembly with the necessary parts in accordance with the extent of the collision damage.



2. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat Type RH Side)
(Click here)


3. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
(Click here )


4. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Climate Control Seat System)


    B357316
  1. Detach the 2 hooks and disconnect the 2 rubber bands.



    B360690E01
  1. Apply protective tape to the locations shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B360691E01
  1. Insert a screwdriver in the clearance between the front seatback board sub-assembly LH and separate type front seatback assembly.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Point (A)

  1. Place the screwdriver at point (A) shown in the illustration and move the screwdriver in the direction of the arrow to detach the 2 guides and remove the 2 seatback board clips from the front seatback board sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.



    B360692
  1. Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 guides and remove the front seatback board sub-assembly LH.



5. REMOVE FRONT SEATBACK BOARD CLIP (w/ Climate Control Seat System)


    B360693
  1. Remove the 2 front seatback board clips from the separate type front seatback spring assembly.



6. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)


    B239173E01
  1. Remove the rubber band from the separate type front seat cushion spring assembly.
    Text in Illustration 
    *1
    Rubber Band



    B239238E01
  1. Detach the claw to disconnect the airbag connector.

  1. Detach the 3 airbag wire harness clamps.

  1. Detach the fastening tape to disconnect the airbag wire harness.
    Text in Illustration 
    *1
    Fastening Tape



    B277849
  1. Remove the 3 hog rings.



    B239194
  1. Open the 2 fasteners and separate type front seatback cover.



    B357314
  1. Remove the nut, detach the 2 hooks to disconnect the seatback cover bracket from the separate type front seatback spring assembly.



    B239198
  1. Using a screwdriver, detach the 4 claws to remove the 2 front seat headrest supports.

  1. Remove the separate type front seatback cover with pad from the separate type front seatback spring assembly.



7. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)


  1. w/o Climate Control Seat System:



      B239173E01
    1. Remove the rubber band from the separate type front seat cushion spring assembly.
      Text in Illustration 
      *1
      Rubber Band



    2. B239174E01
    3. Detach the claw to disconnect the airbag connector.

    4. Detach the 3 airbag wire harness clamps.

    5. Detach the fastening tape to disconnect the airbag wire harness.
      Text in Illustration 
      *1
      Fastening Tape



    6. B277849
    7. Remove the 3 hog rings.



    8. Open the 2 fasteners and separate type front seatback cover.


      B242232E01


      Text in Illustration 
      *A
      for Cloth Seat
      *B
      for Synthetic Leather Seat



    9. B247934
    10. Remove the nut and detach the 2 hooks to disconnect the seatback cover bracket from the separate type front seatback spring assembly.



    11. B239198
    12. Using a screwdriver, detach the 4 claws to remove the 2 front seat headrest supports.

    13. Remove the separate type front seatback cover with pad from the separate type front seatback spring assembly.



  1. w/ Climate Control Seat System:



      B357320E01
    1. Detach the claw to disconnect the airbag connector.

    2. Detach the 3 airbag wire harness clamps.

    3. Detach the fastening tape to disconnect the airbag wire harness.
      Text in Illustration 
      *1
      Fastening Tape



    4. B360653
    5. Detach the 7 hooks.



    6. B247933
    7. Remove the 5 hog rings.



    8. B247934
    9. Remove the nut and detach the 2 hooks to disconnect the seatback cover bracket from the separate type front seatback spring assembly



    10. B239198
    11. Using a screwdriver, detach the 4 claws to remove the 2 front seat headrest supports.

    12. Remove the separate type front seatback cover with pad from the separate type front seatback spring assembly.



8. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B274337
  1. Detach the 2 clamps to disconnect the front seat side airbag wire harness.



    B274336
  1. Using an E10 "TORX" socket wrench, remove the 2 nuts and front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.