Home › Brake › BRAKE (FRONT) › FRONT BRAKE

FRONT BRAKE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for RH and LH sides.
  2. The procedure listed below is for LH side.



1. INSTALL FRONT DISC
  1. When reusing the disc

    1. Align the matchmarks placed when removing, and install the front disc to the axle hub.

  1. When replacing the front disc

    1. Install a new front disc to the axle hub and measure the disc runout (Click here).

  1. Temporarily tighten the hub nut and fix the front disc to the axle hub.



2. INSTALL CARRIER


    C257510
  1. Install the carrier with the 2 new bolts.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



3. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH


    C261019
  1. Apply a light layer of lithium soap base glycol grease to the inner face of the 2 new front disc brake cylinder slide bushes as shown in the illustration.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease



4. INSTALL BUSH


    C261020
  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin with a new bush.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease

  1. Install the bush to the No. 2 front disc brake cylinder slide pin.



5. INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN


    C261021
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of the No. 2 front disc brake cylinder slide pin, as shown in the illustration.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease

  1. Install the No. 2 front disc brake cylinder slide pin to the carrier.



6. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN


    C261022
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of the front disc brake cylinder slide pin, as shown in the illustration.
    Text in Illustration 
    V100144
    Lithium Soap Base Glycol Grease

  1. Install the front disc brake cylinder slide pin to the carrier.



7. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE (LOWER)


    C256671
  1. Apply MP grease to the front disc brake pad support plate (lower) as shown in the illustration.
    Text in Illustration 
    V100144
    MP Grease



8. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE (UPPER)

HINT:
Use the same procedure as for the front disc brake pad support plate (lower).



9. INSTALL FRONT DISC BRAKE CYLINDER SUB-ASSEMBLY


    C259984
  1. Apply disc brake grease to both sides of the shim.
    Text in Illustration 
    V100144
    Disc Brake Grease

  1. Install the covers (shim) to each front disc brake pad.



  1. Install the disc brake pads, covers (shim) and shims to the carrier.


    C256646E01


    Text in Illustration 
    *1
    Cover (Shim)
    *2
    Shim
    *3
    Disc Brake Pad
    -
    -



10. INSTALL FRONT DISC BRAKE CYLINDER SUB-ASSEMBLY


    C256645
  1. Install the front disc brake cylinder assembly LH to the carrier with the 2 bolts.

    Torque:
    26 N*m{ 270 kgf*cm , 19 ft.*lbf }



11. CONNECT NO. 1 FRONT FLEXIBLE HOSE
  1. Install the No. 1 front flexible hose to the disc brake cylinder assembly with 2 new gaskets and the new union bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



12. ADD BRAKE FLUID
  1. Remove the brake master cylinder reservoir filler cap.

  1. Fill the reservoir with brake fluid.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

    NOTICE:
    Make sure that there is sufficient brake fluid in the reservoir.



13. BLEED BRAKE LINE


C256648

NOTICE:
  1. Bleed the brake line of the wheel farthest from the master cylinder first.
  2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brake lines.

  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1

  1. When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2

  1. Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and a new brake fluid comes out.

  1. Tighten the bleeder plug completely.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Repeat the above steps to replace the brake fluid of the brake lines for each wheel.



14. INSPECT FLUID LEAK


15. INSPECT FLUID LEVEL


    C259961E01
  1. Check the fluid level.
    Text in Illustration 
    *a
    MAX Line
    *b
    MIN Line
    If brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

    NOTICE:
    If using a dropper to adjust the fluid amount, make sure that the dropper has not been used with mineral oils, water or deteriorated brake fluid. Sealed areas may deteriorate and lead to fluid leaks, or the fluid may deteriorate and lead to decreased efficiency.



16. INSTALL FRONT WHEEL

Torque:
120 N*m{ 1224 kgf*cm , 89 ft.*lbf }