Home › Engine / Hybrid System › FA20 ENGINE CONTROL › THROTTLE BODY

THROTTLE BODY > INSTALLATION

for Preparation Click here



1. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Install a new gasket to the intake manifold.

  1. Connect the 2 water by-pass hoses to the throttle with motor body assembly with the 2 clamps.

  1. Install the throttle with motor body assembly to the intake manifold with the 4 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the throttle with motor body assembly connector.



2. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
  1. Install the air cleaner cap with air cleaner hose with the 3 blots.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the air cleaner cap with air cleaner hose with the 2 hose clamps.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Connect the No. 2 ventilation hose.

  1. Connect the mass air flow meter connector.

  1. Engage the wire harness clamp and install the wire harness to the air cleaner cap.



3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL



4. ADD ENGINE COOLANT

HINT:
Before replenishing the coolant, turn the A/C switch off. (w/ Air Conditioning System)

  1. Tighten the radiator drain cock plug.

  1. Pour in coolant of the specified density until it reaches the base of the entrance to the water inlet.

    HINT:
    1. The coolant contains anti-freeze and anti-rust agents for use with engines with aluminum cylinder blocks. Using other than the specified coolant may cause rust, so be sure to use Toyota SLLC 50 Blue.
    2. Crimp the inlet and outlet radiator hoses several times by hand, and add water if the water level in the entrance water inlet drops.
    3. The coolant quantity includes the quantity in the reserve tank.



    A279728
  1. Open the air bleed plug on the heater hose side. (for LHD)



    A279727
  1. Open the air bleed plug on the heater hose side. (for RHD)

  1. If the water level in the entrance to the water inlet drops, pour coolant in until it reaches the base of the entrance to the water inlet.

  1. Close the air bleed plug when the coolant begins to come out of the air bleed valve on the heater hose side.

  1. Pour in coolant of the specified concentration until it reaches the "FULL" level of the radiator reserve tank.

  1. Close the radiator cap. [*1]

  1. Start the engine, race it 5 to 6 times at under 3000 rpm or less, and then stop the engine. [*2]

    HINT:
    Finish this operation within 40 seconds.

  1. 1 minute after stopping the engine, remove the radiator cap and pour coolant in if the water level in the entrance to the water inlet has dropped. [*3]

  1. Repeat operations [*1], [*2], and [*3] until the water level in the entrance to the water inlet does not drop.

    HINT:
    Perform before the engine warms up, as the air that comes out of the inlet radiator hose will travel to the radiator side when the engine warms up and the thermostat opens.

  1. Close the radiator cap and the radiator reserve tank cap.

  1. Start the engine, set the heater on full warm, and then run it with the blower speed set to "LO".

  1. Run the engine at 2000 rpm or less until the radiator fan starts and stops. [*4]

    HINT:
    To prevent overheating, pay attention to the water temperature.

  1. Stop the engine and wait until the coolant temperature drops to 30 °C (86 °F) or less. [*5]

  1. Remove the radiator cap and, if the volume of coolant has dropped, pour coolant in until it reaches the base of the entrance to the water inlet and until it reaches the "FULL" level in the radiator reserve tank. [*6]

  1. Close the radiator cap. [*7]

  1. Set the heater to full warm, and, with the blower speed set to "LO", race the engine at 3000 rpm or less. [*8]

  1. At this point, if the engine coolant can be heard flowing in the heater core, repeat operations [*4], [*5], [*6], [*7], and [*8].



    A280287
  1. When the water level no longer drops, adjust the water level so that the water level in the radiator reserve tank reaches the "FULL" line.



5. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.*

*: w/ Air Conditioning System


    A279737
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 20 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



6. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY

NOTICE:
Perform the following procedure after replacing the ECM, throttle with motor body assembly or any throttle with motor body assembly components.

  1. Turn the ignition switch to ON without operating the accelerator pedal.

    NOTICE:
    If the accelerator pedal is operated, perform the above steps again.

  1. Connect the GTS to the DLC3 and clear the DTCs (Click here).

  1. Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range when the A/C is switched off.

    Standard:
    Condition
    Engine Idle Speed
    A/C switched off
    650 to 800 rpm

    NOTICE:
    1. Be sure to perform this step with all accessories off.
    2. Make sure that the shift lever is in neutral (for manual transmission).
    3. Make sure that the shift lever is in N or P (for automatic transmission).

  1. Enter the following menus: Data List / Throttle Sensor Volt%. Fully depress the accelerator pedal and check that the value is 80 to 90%.

  1. Perform a road test and confirm that there are no abnormalities.