Home › Engine / Hybrid System › FA20 FUEL › FUEL INJECTOR (for Port Injection)

FUEL INJECTOR (for Port Injection) > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY
  1. Apply gasoline to a new fuel injector O-ring and a new fuel injector grommet, and then install them to the injector.

    NOTICE:
    Check that there is no damage or foreign material in the groove of the injector when installing the fuel injector O-ring and fuel injector grommet.

  1. Install the 4 fuel injector assemblies to the fuel delivery pipe.

    NOTICE:
    1. Check that there are no foreign objects or scratches in the insertion opening of the fuel delivery pipe.
    2. Take sufficient care not to twist the O-ring.
    3. If the injector does not rotate smoothly after installing it to the fuel delivery pipe, remove the injector and reinstall it with a new O-ring.



2. INSTALL FUEL INJECTOR SEAL (for Bank 1)
  1. Install 2 new fuel injector seals.



3. INSTALL FUEL INJECTOR SEAL


4. INSTALL FUEL INJECTOR SEAL (for Bank 2)
  1. Install 2 new fuel injector seals.



5. INSTALL FUEL DELIVERY PIPE (for Bank 1)
  1. Install the fuel delivery pipe (with injector) to the intake manifold with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Engage the clamp to connect the wire harness.

  1. Connect the 2 fuel injector assembly connectors.

    HINT:
    Connect the connector, aligning it with the baffles on the fuel injector assembly on the fuel delivery pipe.

  1. Connect the fuel delivery tube to the fuel delivery pipe (Click here).



6. INSTALL FUEL DELIVERY PIPE (for Bank 2)
  1. Install the fuel delivery pipe (with injector) to the intake manifold with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the 2 injector connectors and clamp.

    HINT:
    Connect the connector, aligning it with the baffles on the fuel injector assembly on the fuel delivery pipe.

  1. Connect the fuel delivery tube to the fuel delivery pipe (Click here).



7. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY (for Clamp Type)
  1. Connect the No. 2 fuel vapor feed hose to the fuel delivery pipe sub-assembly.

  1. Install the fuel delivery pipe sub-assembly to the intake manifold with the bolt.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }



8. CONNECT NO. 1 FUEL HOSE (for Metal Type)
  1. Connect the No. 1 fuel hose to the fuel delivery pipe with the clamp.

  1. Tighten the hose clamp bolt.



9. INSTALL INJECTOR COVER (for Bank 2)
  1. Install the injector cover (for bank 2) to the intake manifold with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Install the wire harness clamp bracket to the injector cover (for bank 2) with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



10. CONNECT NO. 2 FUEL HOSE (for Metal Type)
  1. Connect the No. 2 fuel hose to the fuel delivery pipe sub-assembly with the clamp.



11. CONNECT NO. 3 FUEL HOSE (for Metal Type)
  1. Connect the No. 3 fuel hose to the fuel delivery pipe sub-assembly (Click here).



12. CONNECT NO. 1 FUEL HOSE (for Metal Type)
  1. Connect the No. 1 fuel hose to the fuel delivery pipe (Click here).



13. INSTALL INJECTOR COVER (for Bank 1)
  1. Install the injector cover (for bank 1) to the intake manifold with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Engage the 4 clamps to install the wire harness to the injector cover (for bank 1).



14. INSTALL INJECTOR DRIVER

NOTICE:
  1. Be careful not to drop or strike the injector driver.
  2. The injector driver is grounded at the bolt and the nut. To ensure that it is grounded, clean all oil and foreign matter from the installation areas of the injector driver and engine before installing the injector driver.

  1. Install the injector driver with the 3 bolts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }



    A279731E03
  1. Connect the 4 connectors to the injector driver. Move the lock levers in the direction indicated by the arrow to lock the 3 connectors.
    Text in Illustration 
    *1
    Lock Lever
    V100135
    Lock with Connector
    V100136
    Normal Connector



15. INSTALL CHAMBER ASSEMBLY
(Click here)


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL



17. INSPECT FOR FUEL LEAK
  1. Connect the GTS to the DLC3.

    1. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    2. Turn the GTS on.

    3. Enter the following menus: Power train / Engine / Active Test / Control the Fuel Pump / Speed.

  1. Check the fuel pump operation.

    1. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard.
      If no sound can be heard, check the EFI MAIN 1 relay, fuel pump, ECM and wiring connector.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance.
      If there is a fuel leak, repair or replace parts as necessary.