Home › Engine / Hybrid System › FA20 FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 FUEL TANK CUSHION
  1. Install 10 new No. 1 fuel tank cushions to the fuel tank assembly.



2. INSTALL NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY
  1. Install the fuel filter to the No. 2 fuel tank main tube sub-assembly.

  1. Install the No. 2 fuel tank main tube sub-assembly to the fuel tank assembly.



3. INSTALL FUEL TANK TO FILLER PIPE HOSE
  1. Install the fuel tank to filler pipe hose to the fuel tank assembly with the clamp.

  1. Tighten the hose clamp bolt.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



4. INSTALL FUEL TANK ASSEMBLY


    A282901
  1. Inspect the fuel tank cover.

    HINT:
    The fuel tank cover is used as a base when attaching the fuel tank assembly, so inspect for any deformation, cracking, or other damage. If any faults are found, replace with a new one.

  1. Hold the fuel tank assembly with an engine lifter.

  1. Temporarily install the fuel tank assembly to the body with the 2 No. 1 fuel tank bands and 4 bolts.



    A282902
  1. Adjust the position of the fuel tank assembly to achieve the required separation between the front edge of the fuel tank cover and the holes used for fixing the parking brake cable bracket in place.

    Standard:
    42 to 44 mm (1.6535 to 1.7323 in.)



    A282903
  1. Adjust the position of the fuel tank assembly to achieve the required difference in clearance between the left and right sides of the fuel tank assembly and the body.

    Standard:
    Below 2 mm (Below 0.0787 in.)



    A277995E01
  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



5. CONNECT NO. 6 FUEL TANK BREATHER TUBE (for Clamp Type)
  1. Connect the No. 6 fuel tank breather tube with the clamp.



6. CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY (for Metal Type)
  1. Connect the fuel tank vent hose sub-assembly.



7. CONNECT FUEL TANK TO FILLER PIPE HOSE (for Clamp Type)
  1. Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly with the clamp.

  1. Tighten the hose clamp bolt.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



8. INSTALL CHARCOAL CANISTER ASSEMBLY (for Metal Type)


    A282326E01
  1. Connect the quick connector as indicated by the arrows in the order shown in the illustration.



9. CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY (for Metal Type)
  1. Engage the clamp to install the tube.

  1. Connect the fuel tank vent hose sub-assembly with the clamp.



10. CONNECT FUEL TANK TO FILLER PIPE HOSE (for Metal Type)
  1. Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly with the clamp.

  1. Tighten the hose clamp bolt.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



11. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 3 parking brake cable assembly to the parking brake plate with the clamp.

  1. Install the No. 3 parking brake cable assembly to the body with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



12. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Use the same procedure for the No. 2 parking brake cable assembly as for the No. 3 parking brake cable assembly.



13. INSTALL NO. 2 FUEL TANK PROTECTOR (for Clamp Type)
  1. Install the No. 2 fuel tank protector with 2 new nuts and 2 clips.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



14. INSTALL NO. 1 FUEL TANK PROTECTOR (for Clamp Type)
  1. Install the No. 1 fuel tank protector with 2 new nuts and 2 clips.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



15. INSTALL NO. 3 FUEL TANK PROTECTOR (for Metal Type)
  1. Install the No. 3 fuel tank protector with a new nut and 2 clips.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



16. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY
(Click here)


17. INSTALL FUEL TANK RETURN TUBE
  1. Install a new gasket to the fuel tank assembly.



    A280575E01
  1. Apply a light coat of gasoline to a gasket.
    Text in Illustration 
    *1
    Gasket
    *a
    Application area

    NOTICE:
    1. Apply gasoline in the area indicated in the illustration.
    2. Ensure that gasoline does not adhere to the threads of the fuel tank assembly.
    3. Check that there is no fuel or foreign matter in the seal section.

  1. Engage the clamp to install the tube and set the fuel tank return tube into the fuel tank assembly.

    NOTICE:
    Be careful not to bend the arm of the No. 2 fuel sender gauge assembly.



    A280579E01
  1. Set the fuel suction tube assembly with pump and gauge within the fuel tank assembly installation position marks.
    Text in Illustration 
    *a
    Installation position marks

  1. Attach a new sheet ring and fuel pump gauge retainer, and temporarily tighten the fuel pump gauge retainer.



  1. Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.

    SST
    09808-14030   (09808-01030, 09808-01050)
    09808-01071  

    NOTICE:
    A291075E01
    Do not apply a claw of SST at the marked part.

    Text in Illustration 
    *a
    Marked Part

    HINT:
    1. Be sure to use SST (claws) as shown in the illustration.
    2. Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.

  1. While securely pressing SST (claws) against the fuel pump gauge retainer ribs, tighten the 4 bolts.

    HINT:
    Install SST while pressing SST (claws) against the fuel pump gauge retainer (towards the center of SST).



    A298983E01
  1. Using SST, tighten the fuel pump gauge retainer.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    NOTICE:
    1. Do not use any tools other than those specified in this operation. Damage to the fuel pump gauge retainer or fuel tank may result.
    2. Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
    3. Make sure to rotate SST horizontally. If SST is rotated at an angle, SST may come off.
    4. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    5. If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.
    6. Check that the fuel suction tube assembly with pump and gauge position marks are within the fuel tank assembly installation position marks, as shown in the illustration.
    7. After tightening to the specified torque, check that it has been tightened to the correct torque.

    HINT:
    1. Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to tighten the fuel pump gauge retainer.
    2. The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.

    Text in Illustration 
    *a
    Position mark
    *b
    Installation position marks



18. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    A282899E01
  1. Set the new gasket to the fuel suction tube assembly with pump and gauge.
    Text in Illustration 
    *1
    Gasket

  1. Connect the fuel tank vent hose sub-assembly (Click here).

    NOTICE:
    1. When connecting the fuel tube connector, do not forcibly pull the fuel return vent tube sub-assembly.
    2. Be careful not to bend the arm of the fuel sender gauge assembly.



    A280578
    A282900E01
  1. Insert the fuel suction tube assembly with pump and gauge inside the fuel tank assembly, and then attach the new gasket which has already been mounted on the fuel suction tube assembly with pump and gauge to the fuel tank assembly.

    NOTICE:
    Gaps or misplaced attachment of the gasket may cause fuel to leak, so make sure that there are no gaps or misalignments anywhere around the gasket when attaching it to the fuel tank assembly.



    A280575E01
  1. Apply a light coat of gasoline to a gasket.
    Text in Illustration 
    *1
    Gasket
    *a
    Application area

    NOTICE:
    1. Apply gasoline in the area indicated in the illustration.
    2. Ensure that gasoline does not adhere to the threads of the fuel tank assembly.
    3. Check that there is no fuel or foreign matter in the seal section.



    A280573E01
  1. Set the fuel suction tube assembly with pump and gauge within the fuel tank assembly installation position marks.
    Text in Illustration 
    *a
    Installation position marks

  1. Attach a new sheet ring and fuel pump gauge retainer, and temporarily tighten the fuel pump gauge retainer.



  1. Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.

    SST
    09808-14030   (09808-01030, 09808-01050)
    09808-01071  

    NOTICE:
    A291075E01
    Do not apply a claw of SST at the marked part.

    Text in Illustration 
    *a
    Marked Part

    HINT:
    1. Be sure to use SST (claws) as shown in the illustration.
    2. Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.

  1. While securely pressing SST (claws) against the fuel pump gauge retainer ribs, tighten the 4 bolts.

    HINT:
    Install SST while pressing SST (claws) against the fuel pump gauge retainer (towards the center of SST).



    A298982E01
  1. Using SST, tighten the fuel pump gauge retainer.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    NOTICE:
    1. Do not use any tools other than those specified in this operation. Damage to the fuel pump gauge retainer or fuel tank may result.
    2. Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
    3. Make sure to rotate SST horizontally. If SST is rotated at an angle, SST may come off.
    4. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    5. If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.
    6. Check that the fuel suction tube assembly with pump and gauge position marks are within the fuel tank assembly installation position marks, as shown in the illustration.
    7. After tightening to the specified torque, check that it has been tightened to the correct torque.

    HINT:
    1. Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to tighten the fuel pump gauge retainer.
    2. The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.

    Text in Illustration 
    *a
    Position mark
    *b
    Installation position marks

  1. Engage the clamp to install the fuel tank main tube to the fuel tank assembly.

  1. Connect the fuel tank main tube (Click here).



19. ADD FUEL


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL



21. INSPECT FOR FUEL LEAK
  1. Connect the GTS to the DLC3.

    1. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    2. Turn the GTS on.

    3. Enter the following menus: Power train / Engine / Active Test / Control the Fuel Pump / Speed.

  1. Check the fuel pump operation.

    1. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard.
      If no sound can be heard, check the EFI MAIN 1 relay, fuel pump, ECM and wiring connector.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance.
      If there is a fuel leak, repair or replace parts as necessary.



22. INSTALL NO. 2 REAR FLOOR SERVICE HOLE COVER
  1. Connect the fuel suction tube assembly with pump and gauge connector.

  1. Install the No. 2 rear floor service hole cover with new butyl tape.



23. INSTALL REAR FLOOR SERVICE HOLE COVER
  1. Connect the fuel tank return tube connector.

  1. Install the rear floor service hole cover with new butyl tape.



24. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH
  1. Engage the hook and install the separate type rear seat cushion assembly LH.

  1. Install the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



25. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.