Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

DTC    B27A5    Open in Front Floor Electrical Key Oscillator Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the indoor electrical key oscillator (front floor). For the certification ECU (smart key ECU assembly) to detect when the key is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the key is transmitted inside the vehicle. DTC B27A5 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and indoor electrical key oscillator (front floor) (between terminals CLG5 and ANTE5, or terminals CG5B and CLGB).

DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A5
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and indoor electrical key oscillator (front floor) (CLG5 - ANTE5, CG5B - CLGB) (1 trip detection logic*1).
  1. Wire harness or connector
  2. indoor electrical key oscillator (front floor)
  3. Certification ECU (smart key ECU assembly)
Any time*2
  1. *1: Only output while a malfunction is present.
  2. *2: Only when the vehicle is stopped.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
When key is in front seat area:
  1. Power source mode does not change when engine switch pressed
  2. Key locked inside vehicle
-

Related Data List and Active Test 
DTC No.
Data List and Active Test
B27A5
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM


B286267E16


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system (for Entry Function) uses a LIN communication system and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".
  5. Indoor electrical key oscillator (front floor) has an antenna coil between CLG3 and CLGB terminals.

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the indoor electrical key oscillator (front floor).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR))
  1. Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  1. Disconnect the D26 indoor electrical key oscillator (front floor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-3 (CLG5) - D26-1 (ANTE5)
    Always
    Below 1 Ω
    D41-2 (CG5B) - D26-3 (CLGB)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D41-3 (CLG5) - Body ground
    Always
    10 kΩ or higher
    D41-2 (CG5B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR))

B271428E16


Text in Illustration 
*a
Component with harness connected
(Certification ECU (smart key ECU assembly))
*b
Waveform
*c
Within approximately 30 seconds from when the door is closed
*d
After approximately 30 seconds from when the door is closed
  1. Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connector.

  1. Reconnect the D26 indoor electrical key oscillator (front floor) connector.

  1. Using an oscilloscope, check the waveform.

    HINT:
    Check that the entry cancel function, which is one of the customizing settings of the entry and start system, is not set (Click here).


    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    D41-3 (CLG5) - D48-11 (GND)
    Procedure:
    1. Engine switch off
    2. Door is open
    3. Door is closed
    4. 30 seconds elapse
    5. Electrical key transmitter sub-assembly not inside vehicle
    2 V/DIV., 500 ms/DIV.
    Pulse generation
    (See waveform)
    D41-2 (CG5B) - D48-11 (GND)
    Procedure:
    1. Engine switch off
    2. Door is open
    3. Door is closed
    4. 30 seconds elapse
    5. Electrical key transmitter sub-assembly not inside vehicle
    2 V/DIV., 500 ms/DIV.
    Pulse generation
    (See waveform)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4.REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR)
  1. Temporarily replace the indoor electrical key oscillator (front floor) with a new or normally functioning one (Click here).


NEXT


5.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    DTC B27A5 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR) WAS DEFECTIVE)