Home › Drivetrain ยท AXLE AND DIFFERENTIAL › DIFFERENTIAL MOUNT CUSHION

DIFFERENTIAL MOUNT CUSHION > INSTALLATION

for Preparation Click here



1. INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION


    C262507E02
  1. Put matchmarks on the rear suspension member and new rear No. 2 differential mount cushion.
    Text in Illustration 
    *a
    Arrow
    *b
    Matchmark

    CAUTION:
    Install the rear No. 2 differential mount cushion with the arrow marks facing upward and downward.



    C260031E01
  1. Using SST, install the rear No. 2 differential mount cushion.

    SST
    09570-18010   (09571-01030, 09571-01040, 09571-01050, 09571-01060, 09571-01070, 09571-01080, 09571-01090)
    Text in Illustration 
    *1
    Rear Suspension Member
    *2
    Rear No. 2 Differential Mount Cushion
    *3
    SST(09571-01090)
    *4
    SST(09571-01070)
    *5
    SST(09571-01050)
    *6
    SST(09571-01080)
    *7
    SST(09571-01040)
    *8
    SST(09571-01030)
    *9
    SST(09571-01060)
    *a
    Hold
    *b
    Turn
    *c
    Start
    *d
    End
    V100135
    Front side

    HINT:
    1. Install the rear No. 2 differential mount cushion while aligning with the matchmark on the rear suspension member and checking misalignment.
    2. Push in the rear No. 2 differential mount cushion until SST (09571-01040) comes into contact with the rear suspension member.

    3. C260033E02
      Make sure that the differential mount cushion is aligned within 5° from the center.
      Text in Illustration 
      *a
      5°



2. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION


    C262506E01
  1. Put matchmarks on the rear suspension member and new rear No. 1 differential mount cushion.
    Text in Illustration 
    *a
    Triangle Mark
    *b
    Matchmark

    NOTICE:
    Install the rear No. 1 differential mount cushion with the triangle mark facing upward.



    C260028E02
  1. Using SST, install the rear No. 1 differential mount cushion.

    SST
    09570-18020   (09571-01120, 09571-01130, 09571-01140, 09571-01150, 09571-01160, 09571-01170, 09571-01180, 09571-01190)
    09922-10010  
    Text in Illustration 
    *1
    Rear Suspension Member
    *2
    Rear No. 1 Differential Mount Cushion
    *3
    SST(09571-01150)
    *4
    SST(09571-01130)
    *5
    SST(09571-01190)
    *6
    SST(09571-01120)
    *7
    SST(09571-01170)
    *8
    SST(09571-01140)
    *9
    SST(09571-01160)
    *10
    SST(09571-01180)
    *11
    SST(09922-10010)
    *a
    Hold
    *b
    Turn
    *c
    Start
    *d
    End
    V100135
    Front side

    NOTICE:
    1. Install the rear No. 1 differential mount cushion while checking that SST and the rear No. 1 differential mount cushion are not at an angle.
    2. If the rear No. 1 differential mount cushion is pushed in at an angle, the installation becomes difficult. Be sure to set SST on the rear No. 1 differential mount cushion with no clearance.

    HINT:
    1. Install the rear No. 1 differential mount cushion while aligning with the matchmark on the rear suspension member and checking misalignment.
    2. Push in the rear No. 1 differential mount cushion until SST (09571-01130) comes into contact with the rear suspension member.

    3. C260032E02
      Make sure that the differential mount cushion is aligned within 3° from the center.
      Text in Illustration 
      *a
      3°



3. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
(Click here)


4. INSTALL REAR STABILIZER BAR
(Click here)


5. INSTALL TAIL EXHAUST PIPE ASSEMBLY
  1. Install the 4 cushion rubbers and the tail exhaust pipe assembly.



6. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
(Click here)