Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE

SPIRAL CABLE > REMOVAL

for Preparation Click here



1. REMOVE STEERING WHEEL ASSEMBLY
(Click here)


2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


3. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    B279793
  1. Check the colored part as shown in the illustration.
    Text in Illustration 
    V100144
    Colored Part
    If the colored part shown in the illustration cannot be confirmed, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable with sensor sub-assembly with a new one.



4. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag)
(Click here)


5. REMOVE INSTRUMENT SIDE PANEL (w/o Knee Airbag)

HINT:
Use the same procedure as for the RH side.



6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)


    B312955
  1. Remove the 2 screws.



    B312956
  1. Disengage the 4 clips.

  1. Disengage the 4 claws and separate the No. 1 instrument panel under cover sub-assembly.



    B313000E01
  1. w/ Automatic Air Conditioning System for RHD:

    1. Disengage the guide and disconnect the aspirator hose.

    2. Disconnect the connector.

  1. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.
    Text in Illustration 
    *1
    Aspirator Hose



7. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B315188E01
  1. Using a moulding remover, disengage the 2 claws and 4 clips to remove the center instrument cluster finish panel sub-assembly.
    Text in Illustration 
    *1
    Moulding Remover



8. REMOVE METER HOOD SUB-ASSEMBLY


    B315191
  1. Remove the screw.

  1. Disengage the 12 claws, and then pull out the meter hood sub-assembly diagonally upwards to remove it.



9. REMOVE UPPER INSTRUMENT PANEL METER ORNAMENT


    B316758
  1. Remove the screw.

  1. Disengage the 6 claws and 2 clips.



    B316759
  1. Disengage the 2 claws that are holding the upper instrument panel meter ornament and steering column cover together.

  1. Disconnect the connector and remove the upper instrument panel meter ornament.



10. REMOVE STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)


    C260477
  1. Disengage the 4 claws and remove the steering column cover support.



11. REMOVE LOWER STEERING COLUMN COVER


  1. w/ Knee Airbag



      C260510
    1. Remove the 2 screws.

    2. Disengage the 4 claws and remove the lower steering column cover.



  1. w/o Knee Airbag



      C260467
    1. Remove the 2 screws.

    2. Disengage the 6 claws and remove the lower steering column cover.



12. REMOVE UPPER STEERING COLUMN COVER


    C260468
  1. Disengage the 2 claws to remove the upper steering column cover.



13. REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
  1. Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch ON.
  2. Do not rotate the spiral cable sub-assembly without the steering wheel with the battery connected and the ignition switch ON.
  3. Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

  1. Check that the front wheels are facing straight ahead.



    B311356E01
  1. Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.
    Text in Illustration 
    *1
    Slider

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Disconnect the other connector from the spiral cable with sensor sub-assembly.



    B311363
  1. Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.



14. REMOVE SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
  1. Remove the spiral cable sub-assembly from the steering sensor only when replacing it or the steering sensor.
  2. Do not rotate the center section of the steering sensor, as it may deviate from the steering sensor neutral point.



    B313958E01
  1. Disengage the 6 claws, 2 pins and 2 guides to remove the spiral cable sub-assembly from the steering sensor.

    NOTICE:
    Do not damage the guide and claw.

    Text in Illustration 
    *1
    Guide
    *2
    Pin