SPIRAL CABLE > REMOVAL |
| 1. REMOVE STEERING WHEEL ASSEMBLY |
| 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 3. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Check the colored part as shown in the illustration.
![]() | Colored Part |
| 4. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag) |
| 5. REMOVE INSTRUMENT SIDE PANEL (w/o Knee Airbag) |
![]() |
Using a moulding remover, disengage the claw and 4 clips and remove the instrument side panel.
| *1 | Moulding Remover |
| 6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag) |
![]() |
Remove the 2 screws.
![]() |
Disengage the 4 clips.
Disengage the 4 claws and separate the No. 1 instrument panel under cover sub-assembly.
![]() |
w/ Automatic Air Conditioning System for RHD:
Disengage the guide and disconnect the aspirator hose.
Disconnect the connector.
Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.
| *1 | Aspirator Hose |
| 7. REMOVE INSTRUMENT PANEL ORNAMENT (w/ Large Ornament Panel) |
![]() |
Using a moulding remover, disengage the 8 clips and 2 claws to remove the instrument panel ornament.
| *1 | Moulding Remover |
| 8. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Large Ornament Panel) |
![]() |
Using a moulding remover, disengage the 2 claws and 4 clips to remove the center instrument cluster finish panel sub-assembly.
| *1 | Moulding Remover |
| 9. REMOVE METER HOOD SUB-ASSEMBLY |
![]() |
Remove the screw.
Disengage the 12 claws, and then pull out the meter hood sub-assembly diagonally upwards to remove it.
| 10. REMOVE UPPER INSTRUMENT PANEL METER ORNAMENT |
![]() |
Disengage the 6 claws and 2 clips.
![]() |
Disengage the 2 claws that are holding the upper instrument panel meter ornament and steering column cover together.
Disconnect the connector and remove the upper instrument panel meter ornament.
| 11. REMOVE STEERING COLUMN COVER SUPPORT (w/ Entry and Start System) |
![]() |
Disengage the 4 claws and remove the steering column cover support.
| 12. REMOVE LOWER STEERING COLUMN COVER |
w/ Knee Airbag
![]() |
Remove the 2 screws.
Disengage the 4 claws and remove the lower steering column cover.
w/o Knee Airbag
![]() |
Remove the 2 screws.
Disengage the 6 claws and remove the lower steering column cover.
| 13. REMOVE UPPER STEERING COLUMN COVER |
![]() |
Disengage the 2 claws to remove the upper steering column cover.
| 14. REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Check that the front wheels are facing straight ahead.
![]() |
Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.
| *1 | Slider |
Disconnect the other connector from the spiral cable with sensor sub-assembly.
![]() |
Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.
| 15. REMOVE SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Disengage the 6 claws, 2 pins and 2 guides to remove the spiral cable sub-assembly from the steering sensor.
| *1 | Guide |
| *2 | Pin |